Autonics krn100 series 제품 설명서
{카테고리_이름} Autonics krn100 series에 대한 제품 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Autonics krn100 series 3 페이지. 100 mm hybrid recorder
Autonics krn100 series에 대해서도 마찬가지입니다: 사용 설명서 (2 페이지), 사용 설명서 (2 페이지), 매뉴얼 (17 페이지)
페이지 인쇄
TCD210149AC
100 mm Hybrid Recorder
KRN100 Series
PRODUCT MANUAL
For your safety, read and follow the considerations written in the instruction
manual, other manuals and Autonics website.
The specifications, dimensions, etc. are subject to change without notice for product
improvement. Some models may be discontinued without notice.
Features
• 100 mm paper recorder
• Enables to record data without paper with the data logger function
(internal memory and external memory supported to backup data)
• High speed sampling of 25 to 250ms and high speed record of 240mm / H in high
speed graph mode
• 6 recording colors
• Easy parameter setting by quick menu setting
• Enables to set parameters and monitor with USB, RS485, Ethernet communication
• High legibility and setting convenient by graph LCD
• Supports up to 12 channels with slot type input cards
• Supports total 27 kinds of input types
(weight, voltage, current, frequency potentiometer, and etc.)
• Installation space saving with compact design (depth: 168 mm)
ᜢ ᜣ ᜫ
Safety Considerations
• Observe all 'Safety Considerations' for safe and proper operation to avoid hazards.
• symbol indicates caution due to special circumstances in which hazards may occur.
Warning
Failure to follow instructions may result in serious injury or death.
01. Fail-safe device must be installed when using the unit with machinery that may
cause serious injury or substantial economic loss. (e.g. nuclear power control,
medical equipment, ships, vehicles, railways, aircraft, combustion apparatus, safety
equipment, crime / disaster prevention devices, etc.)
Failure to follow this instruction may result in personal injury, economic loss or fire.
02. Do not connect, repair, or inspect the unit while connected to a power source.
Failure to follow this instruction may result in fire or electric shock.
03. Check 'Connections' before wiring.
Failure to follow this instruction may result in fire.
04. Do not touch the unit during or after operation for a while.
Failure to follow this instruction may result in burn or electric shock due to high temperature
of the surface.
05. Do not use the unit in the place where flammable / explosive / corrosive gas, high
humidity, direct sunlight, radiant heat, vibration, impact or salinity may be present.
Failure to follow this instruction may result in explosion or fire.
06. Install on the device panel, and ground to the F.G. terminal separately.
When connecting the F.G. terminal, use AWG16 (1.25 mm²) or over.
Failure to follow this instruction may result in fire or electric shock.
07. Do not disassemble or modify the unit.
Failure to follow this instruction may result in fire.
08. Since Lithium battery is embedded in the product, do not disassemble or burn the
unit.
Failure to follow this instruction may result in fire.
Caution
Failure to follow instructions may result in injury or product damage.
01. Use the unit within the rated specifications.
Failure to follow this instruction may result in fire or product damage.
02. Use a dry cloth to clean the unit, and do not use water or organic solvent.
Failure to follow this instruction may result in fire or electric shock.
03. Keep the product away from metal chip, dust, and wire residue which flow into the
unit.
Failure to follow this instruction may result in fire or product damage.
04. When connecting the power input or measurement input, use AWG20 (0.50 mm²)
cable or over, and tighten the terminal screw with a tightening torque of 0.74 N·m
to 0.90 N·m.
Failure to follow this instruction may result in fire or malfunction due to contact failure.
05. Do not use the load beyond rated switching capacity contact.
Failure to follow this instruction may result in fire, relay broken, contact melt, insulation
failure or contact failure.
06. Use the transmitter output card only for the power for the transmitter.
Failure to follow this instruction may result in output module damage.
07. When connecting the temperature sensor (TC, RTD) or analogue input (voltage,
current) as input to the universal input card, set the jumper pin to the correct place
for the connected input type.
If the jumper pin is placed improperly, it may result in product damage or malfunction.
Cautions during Use
• Follow instructions in 'Cautions during Use' . Otherwise, it may cause unexpected accidents.
• Install a surge absorber at each end of inductive load coil when controlling high-capacity power
relay or inductive load (e.g. magnet).
• Check the polarity of the terminals before wiring the temperature sensor. For RTD temperature
sensor, wire it as 3-wire type, using cables in same thickness and length. For thermocouple (CT)
temperature sensor, use the designated compensation wire for extending wire.
• Keep away from high voltage lines or power lines to prevent inductive noise. In case installing
power line and input signal line closely, use line filter or varistor at power line and shielded wire
at input signal line. Do not use near the equipment which generates strong magnetic force or
high frequency noise.
• This unit may be used in the following environments.
- Indoors (in the environment condition rated in 'Specifications')
- Altitude max. 2,000 m
- Pollution degree 2
- Installation category II