DYNAPAR max jr speed 1 기술 매뉴얼 - 페이지 5

{카테고리_이름} DYNAPAR max jr speed 1에 대한 기술 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DYNAPAR max jr speed 1 12 페이지.

페이지 인쇄

KEYBOARD AND DISPLAY FUNCTIONS

DISPLAY ANNUNCIATORS

~~~----------,

SPD

displayed on speed data lines

ERR

indicates a Error Counter function

PGM

illuminated in Program Mode

GAIN

indicates Gain Setpoint

SET

shown on Setpoint display

RAMP

prompted on Ramp Setpoint

F.S.

indicates a full scale number

ENC

used to calibrate Feedback input

DOWN CURSOR

• Scrolls through Run Mode displays

• Scrolls through Program Mode menu

• "Wraps Around" from last line to first

RIGHT CURSOR

• Selects one digit of numeric data for editing

• Chooses one option from multiple choice menu lines

INCREMENT / ON

• Increases the Speed setpoint toward the Full Scale

Speed at 4 units/sec, or faster, if held

• Increments (adds 1) to the selected digit of numeric data

• Sets Off/On options to On (alternate to Right cursor)

NUMERIC DATA ENTRY

BEFORE

KEYPRESS

AFTER

ISPD

SET

3975 1

[E)

I SPD

SET

39~

ISPD

SET

3975 1

[E)

SET

3975 1

ISPD

SET

39 75 1

Ij)

SET

Y0751

I SPD

SET

Y0 75 1

(j)

I SPD

SET

39 75 1

BEFORE

KEY HELD

AFTER

SET

12801

(jIJ

SET_~

128

Ij)

SET

1282 1

Ij)

SET

1292

~~~

SET

~02

BEFORE

KEYPRESS

AFTER

SPD

Ij)

~--

PGM

00000

PGM

nnnnn

F,S.

l£

uuuu.u

F2:.._~~~

OPERATION ...

PROMPT AND DATA DISPLAY

Selectable decimal point for Speed

Setpoint, Speed Display, and Ramp

RESET / CLEAR

• Clears the numeric data to zero in

Program Mode

RUN/PROGRAM

• Alternates between Run and Program Modes

Disabled when PGM DIS switch is On (up position)

Simulates Stop input (when entering Program

Mode) and Run input (when entering Run Mode)

DECREMENT / OFF

• Decrease the Speed setpoint toward zero at 4

units/sec, or faster, if held

• Decrements (subtracts 1) from the selected digit of

numeric data

Sets On/Off line to Off (alternate to Right cursor)

Most numeric data can be changed by using the Right cursor to

select a digit, which becomes brighter. Then, the Increment (or

Decrement) key will add (or subtract) one from that digit. Note

that carries (or borrows) occur between the selected digit and

all of the digits to its left. With this feature, the Increment will

always increase the setpoint, and the Decrement will always

decrease it. (The carry and borrow functions will not rollover or

rollunder through 00000.)

Setpoint data can also be changed incrementally, rather than

directly. Each press of the Increment (or Decrement) key will

change the value by one LSD. If the key press is held, the

repeat rate will increase, and will increase faster the longer it is

held. A value near the desired number can be reached quickly,

and the Increment and Decrement key can be pressed

individually to get to the exact value.

The Speed Dipslay, Setpoint, Ramp, and Full Scale decimal

point is set with the Increment (and Decrement) key.

The

Increment key will increase the number of decimal places

(shifts decimal point to the left) when no digit is selected.

Page 5