Autonics PSQ-C01 Series 데이터시트 - 페이지 13
{카테고리_이름} Autonics PSQ-C01 Series에 대한 데이터시트을 온라인으로 검색하거나 PDF를 다운로드하세요. Autonics PSQ-C01 Series 14 페이지. Dual lcd display digital pressure sensor
페이지 인쇄Compact, Dual LCD Display Digital Pressure Sensor
Installation
1. Pressure port is divided as standard and option
specification. Therefore, make sure use commercially
available one touch fitting.
● Pneumatic type: Rc1/8, R1/8, NPT1/8
● Fluid type: Rc1/8, R1/8, R1/4, NPT1/4, 9/16-18UNF
2.
Use a spanner (pneumatic type: 12 mm, fluid type: 17mm)
at the metal part of the unit in order not to overload on
the body when connecting one touch fitting.
3. Two different brackets are provided for pneumatic type
and one different brackets are provided for fluid type.
Select proper one with considering your application
environments.
4.
At first, please unscrew hexagon wrench bolt and
assemble the bracket on this unit by fixing hexagon the
wrench bolt.
In this case, tightening torque of hexagon wrench
should be max. 3N . m. It may cause mechanical
problems.
Caution
The tightening torque of one touch fitting should be
max. 10N . m. It may cause mechanical problems.
12mm
spanner
Pneumatic type
<
>
Spring washer
Bracket B
Bracket A
Pneumatic type
<
Bracket C
Fluid type
<
5. PSQ Series has panel bracket (PSO-B02),
front cover (PSO-P01) are sold separately.
When mounting the unit on panel, please follow the
below figure.
When using integrated installation set
Front cover
(PSO-P01)
Mounting panel
(panel thickness 0.8~3.5mm)
Pneumatic/Fulid type
<
17mm
spanner
Fluid type
<
>
Hexagon wrench
bolt (M3×6)
>
>
Panel bracket
(PSO-B02)
Body
(PSQ)
>
When using separate installation set
Front panel bracket
Front cover
(PSO-P02)
Mounting panel
(panel thickness: 0.5 to 7mm)
Pneumatic type
<
6. Do not pull the cable with a tensile strength of 30N or over.
Proper Usage
Caution
PSQ Series is for sensing of non corrosive gas.
Do not use this product at corrosive gas or flammable
gas, etc.
ᆞ 12-24VDC model, power supply should be insulated and
limited voltage/current or Class 2, SELV power supply
device.
ᆞ Do not insert any sharp or pointed object into pressure
port. Failure to follow these instructions may result in
malfunction and damage to the sensor.
ᆞBe sure that this unit must avoid direct touch with water,
oil, thinner, etc.
ᆞDo not use the product in preparation time (within 3 sec).
for operating after power-on.
ᆞWhen using switching mode power supply, frame ground
(F.G.) terminal of power supply should be grounded.
+
-
SMPS
F.G.
ᆞAvoid wiring with power line or high voltage line.
It may cause malfunction by noise.
ᆞWhen moving this unit from cold place to warm place,
please remove the humidity on the cover.
ᆞDo not press the setting button with sharp or pointed
object.
ᆞDo not apply a tensile strength in excess of 30N to the
cables or connector.
ᆞThis unit may be used in the following environment.
① Indoors
② Altitude max. 2,000m
③ Pollution degree 3
④ Installation category II
(PSO-B04)
Body
(PSQ)
Rear panel bracket
(PSO-B04)
>
G-21
SENSORS
CONTROLLERS
MOTION DEVICES
SOFTWARE
(A)
Photoelectric
Sensors
(B)
Fiber Optic
Sensors
(C)
LiDAR
(D)
Door/Area
Sensors
(E)
Vision
Sensors
(F)
Proximity
Sensors
(G)
Pressure
Sensors
(H)
Rotary
Encoders
(I)
Connectors/
Connector Cables/
Sensor Distribution
Boxes/ Sockets