Frigidaire 000-BTU Through-the-Wall Air Conditioner 사용 및 관리 매뉴얼 - 페이지 7
{카테고리_이름} Frigidaire 000-BTU Through-the-Wall Air Conditioner에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Frigidaire 000-BTU Through-the-Wall Air Conditioner 11 페이지. Wiring schematic
Frigidaire 000-BTU Through-the-Wall Air Conditioner에 대해서도 마찬가지입니다: 배선 다이어그램 (1 페이지)
페이지 인쇄
Air Conditioner Features
(continued)
TO OPERATE ON FAN ONLY:
Temp/Timer
Auto Temp
Hi
Med
Lo
Heat
Cool
Fan
Speed
Energy Saver
Fan Only
Temp/Timer
Mode
Timer
Note: Use this function only when cooling is not desired, such as for room air
circulation. You can choose any fan speed you prefer,EXCEPT AUTO FAN.
During this function, the display will show the actual current temperature, not the set temperature as in the cooling mode.
Fan Only cannot be selected when the unit is in the 'Remote Sensing' Mode. (On those units with that feature).
TO USE THE
ENERGY SAVER FEATURE:
Temp/Timer
Auto Temp
Hi
Med
Lo
Heat
Cool
Fan
Speed
Energy Saver
Fan Only
Temp/Timer
Mode
Timer
Note: In this mode, the fan will continue to run for 3 minutes after the compressor shuts off. The fan then cycles on for 2
minutes at 10 minute intervals until the room temperature is above the set temperature, at which time the unit cooling
system starts again.
TIMER-DELAY
START/STOP FEATURE:
Temp/Timer
Auto Temp
Hi
Med
Lo
Heat
Cool
Fan
Speed
Energy Saver
Fan Only
Temp/Timer
Mode
Timer
Note 1: For Delay Stop, the unit must be in the ON position.
Note 2: For Delay Start, the unit must be in the OFF position.
To adjust timer setting, tap or hold the UP arrow ( ) or DOWN arrow (v) to change the delay time by .5 hour increments up to
10 hours, then by 1 hour increments up to 24 hours. The control will count down the timer remaining until start (8, 7.5, 7,
etc.). The Delay Start mode automatically selects cooling with maximum Fan Speed. The temperature maintained will be the
same as previously set. To change the set temperature, press "COOL" then Up or Down arrows until the desired temperature
is indicated on the display. After 5 seconds, the control will automatically change the display back to the hours remaining
until the unit will start/stop. Turning the unit "ON" or "OFF" at any timer will cancel the Delay Start/Stop function. The delay
Start/Stop feature will work until the unit either starts or stops. Once this has happened then the above steps have to be
repeated again.
Check
Sleep
Filter
MODE BUTTON
Remote
Sensing
Check
Sleep
Filter
Remote
Sensing
ENERGY SAVER
Check
Sleep
Filter
PRESS TEMP/TIMER
Remote
Sensing
V
LIGHT ON
DO THIS:
PRESS
CHOOSE
FAN ONLY
LIGHT ON
DO THIS:
PRESS
MODE BUTTON
CHOOSE
FIRST
DO THIS:
PRESS TIMER
BUTTON
THEN
DO THIS:
BUTTON
7
YOU WILL SEE:
Temp/Timer
Auto Temp
Hi
Med
Lo
Heat
Cool
Fan
Speed
Energy Saver
Fan Only
Temp/Timer
Mode
Timer
YOU WILL SEE:
Temp/Timer
Auto Temp
Hi
Med
Lo
Heat
Cool
Fan
Speed
Energy Saver
Fan Only
Temp/Timer
Mode
Timer
YOU WILL SEE
THE TIME CHOSEN:
Temp/Timer
Auto Temp
Hi
Med
Lo
Heat
Cool
Fan
Speed
Energy Saver
Fan Only
Temp/Timer
Mode
Timer
LIGHT ON
Check
Sleep
Filter
Remote
Sensing
Check
Sleep
Filter
Remote
Sensing
Check
Sleep
Filter
Remote
Sensing