Autonics SCM-US48I 매뉴얼 - 페이지 2

{카테고리_이름} Autonics SCM-US48I에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Autonics SCM-US48I 11 페이지. Communication converter
Autonics SCM-US48I에 대해서도 마찬가지입니다: 빠른 매뉴얼 (11 페이지), 매뉴얼 (13 페이지), 제품 설명서 (2 페이지)

페이지 인쇄

SCM Series

Specifications

SCM-WF48

Model

Power supply

Allowable voltage range

Communication type

Isolation resistance

Protection circuit

Dielectric strength

Noise resistance

Vibration

Shock

Ambient

Environ

temperature

-ment

Ambient humidity 35 to 80%RH, storage: 35 to 80%RH

Protection

Mounting

Accessories

※ 1

Weight

※ 1: The weight is with packaging and the weight in parentheses is only unit weight.

※ Environment resistance is rated at no freezing or condensation.

RS485 communication specifications

Connection

RS485

Standard

EIA RS485

Protocol

Modbus RTU

Com. method

2-wire half duplex

Synchronous

method

Asynchronous

Effective com.

Max. 800m

distance

4800, 9600, 19200, 38400, 57600,

Com. speed ※1

115200bps

(factory default: 115200bps)

Data bit ※1

5bit,6bit,7bit,8bit(factory default:8bit)

Stop bit ※1

1bit, 2bit(factory default: 1bit)

Parity bit ※1

None, Even, Odd(factory default: None)

Multi-drop

Max. 31 Multi-drop

4-wire screw terminal

Connection type

(2-wire communication method)

※ 1: You can set this by DAQMaster.

SCM-US48I / SCM-38I / SCM-US

Model

Power supply

Power consumption

※ 2

Max. com speed

Communication type

Available com. distance

Multi-drop

Data bit

※ 2

Protocol

Stop bit

Parity bit

Connection type

Isolation type

Dielectric strength

※ 1: USB bus power is supplied from PC or USB host controller.

※ 2: Protocol and communication speed are set by Hyper terminal. DAQMaster, ParaSet, Modbus Poll.

When communicating with Autonics products, set communication speed to 9,600bps.

S-32

SCM-WF48

24VDC

12-28VDC

RS485, USB, Wi-Fi

Min. 200 MΩ(at 500 VDC megger between external terminal and case)

Reverse polarity protection circuit, surge protection circuit

1,000VAC 50/60Hz for 1 min.(between external terminal and case)

±500 V the square wave noise(pulse width: 1㎲) by the noise simulator

1.5 mm amplitude at frequency or 300m/s

500m/s

(approx. 50G) in each of X, Y, Z directions for 3 times

-10 to 55℃, storage: -20 to 60℃

IP20(IEC standards)

DIN rail or panel mounting

USB 2.0 Mini 5P type cable (length: 1 m),

Connector for RS-485 (4-pin, male type) 1EA

Approx. 160g(approx. 57g)

SCM-US48I

5VDC USB bus Power

Max. 1W

1,200 to 115,200bps(Recommended : 9,600bps)

Half duplex type

USB: Max. 1m ± 30%

RS485: Max.1.2km

Max. 31 multi-drop

5 to 8 data bits

1 or 2 stop bits

None/Odd/Even

USB: B type connector

RS485: 4-wire screw terminal(2wire communication type)

Isolation

●Between terminals and case:

200VAC 50/60Hz for 1 min.

●Between USB and RS485:

2500VAC 50/60Hz for 1 min.

of 10 to 55 Hz(for 1min.) in each of X, Y, Z directions for 2 hours

Wi-Fi communication specifications

Protocol

TCP/IP(IPv4)

Standard

802.11 b/g/n(IEEE 802.11b) compatible

Com. speed

Max. 11 Mbps

Frequency range 2.4 to 2.497 GHz

Security

WEP, WPA, WPA2-PSK, Enterprise

Antenna

2dBi external antenna

Com. distance

Max. 100 m

USB communication specifications

Power

5 V, 500 mA

Standard

USB 2.0(compatible sub-transmission)

Com. method

2-wire half duplex

Connections

USB 2.0 Mini 5P type(Male)

SCM-38I

12-24VDC ± 10%

Max. 1.7W

Max. 1.2km

RS232: D-sub 9Pin

●Between terminals and case:

200VAC 50/60Hz for 1 min.

●Between RS232C and RS485:

2500VAC 50/60Hz for 1 min.

SCM-US

※ 1

5VDC USB bus Power

Max. 1W

1.5m(not extension)

USB: A type connector

Earphone jack(4 pole stereo phone

plug)

Non-isolation