Autonics BJ3M-PDT Series 제품 설명서 - 페이지 3

{카테고리_이름} Autonics BJ3M-PDT Series에 대한 제품 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Autonics BJ3M-PDT Series 7 페이지. Rectangular photoelectric sensor

페이지 인쇄

Sensitivity Adjustment

• Set the adjuster for stable Light ON area, minimizing the effect of the installation environment.

• Use the offered adjustment screwdriver. Do NOT turn with excessive force to prevent

product damage.

• The steps below are based on Light ON mode.

STEP Status

Description

Turn the adjuster from MIN to MAX sensitivity and

Received

check the position (A) where the operation indicator

activates under the light ON area.

Turn the adjuster from (A) to MAX and check the

position (B) where the operation indicator activates

Interrupted

under the light OFF area.

If the operation indicator does NOT activate at the

MAX (maximum sensitivity): MAX = (B).

Set the adjuster at the mid position between (A) and

(B) for optimal sensitivity.

Dimensions

• Unit: mm, For the detailed drawings, follow the Autonics website.

10.6

C or E

D or E

A or B

Through-beam

Polarized

retroreflective

Optical axis of emitter

Optical axis of receiver

Operation indicator (red)

■ Reflector (MS-2A)

2-Ø3.8

2.5

3.25

8.5

40.5

10.6

2.7

M3 BOLT, NUT

Reflective

Stability indicator (green)

Power indicator of emitter (green)

■ Bracket A

Specifications

Model

Sensing type

Sensing distance

Sensing target

Min. sensing target

Hysteresis

Black/white difference

Response time

Light source

Peak emission

wavelength

Min. spot size

Sensitivity adjustment

Mutual interference

prevention

Operation mode

Indicator

Approval

Unit weight (packaged) ≈ 90 g (≈ 115 g)

01) Reflector (MS-2A)

02) Non-glossy white paper 50 × 50 mm

03) Non-glossy white paper 100 × 100 mm

04) -10% of max. sensing distance, Non-glossy white paper

05) Only for the emitter

Ø 3.5, 2m

Model

Sensing type

Sensing distance

Sensing target

Hysteresis

Response time

Light source

Peak emission

wavelength

Sensitivity adjustment

Mutual interference

prevention

3.4

Operation mode

Ø3.4

Indicator

Approval

Unit weight (packaged) ≈ 45 g (≈ 70 g)

01) Non-glossy white paper 100 × 100 mm

02) Non-glossy white paper 300 × 300 mm

03) Transparent Glass 50 × 50 mm, t = 3.0 mm

Power supply

Ø3.4

Current consumption

Through-beam

Reflective

Control output

Load voltage

Load current

Residual voltage

Protection circuit

Insulation resistance

Noise immunity

Dielectric strength

Vibration

Shock

Ambient illuminance

(receiver)

Ambient temperature

Ambient humidity

Protection rating

Connection

Cable spec.

Wire spec.

Material

BJ□-TDT-□

BJ3M-PDT-□

BJ□-BDT-□

Polarized

Through-beam

BGS reflective

retroreflective

10 to 30

3 m

01)

02)

Opaque materials,

Opaque materials

translucent materials

≥

Ø 8

Ø 12

≥ Ø 75 mm

≤ 10% of sensing

distance

≤ 10% of sensing

distance

≤ 1 ms

≤ 1.5 ms

Red

Infrared Red

Red

650

660

850

660 nm

≈ Ø 5.0

YES (Adjuster)

YES

Light ON mode - Dark ON mode selectable (Adjuster)

Operation indicator (red), stability indicator (green), power indicator (green)

ᜢ ᜽ ᜫ

≈ 60 g (≈ 85 g)

≈ 50 g

BJ□-DDT-□

BJG30 -DDT

Diffuse reflective

100 mm

300 mm

1 m

15 mm

01)

02)

Transparent glass or opaque materials,

Opaque materials, translucent materials

translucent materials

≤ 20% of sensing distance

≤ 1 ms

Infrared

Red

Infrared

850 nm

660 nm

850 nm

YES (Adjuster)

YES

Light ON mode - Dark ON mode selectable

Light ON

(Adjuster)

Operation indicator (red),

stability indicator (green)

ᜢ ᜽ ᜫ

≈ 45 g

12-24 VDCᜡ ±10 % (ripple P-P: ≤ 10%)

It depends on the sensing type

Emitter: ≤ 20 mA, receiver: ≤ 20 mA

≤ 30 mA

NPN open collector output / PNP open collector output model

≤ 26.4 VDCᜡ

≤ 100 mA

NPN : ≤ 1 VDCᜡ, PNP : ≤ 2.5 VDCᜡ (BGS reflective type : ≤ 2 VDCᜡ)

Reverse power protection circuit, output short overcurrent protection circuit

≥ 20 MΩ (500 VDCᜡ megger)

±240 VDCᜡ the square wave noise (pulse width: 1 ㎲) by the noise simulator

Between the charging part and the case: 1,000 VACᜠ 50/60 Hz for 1 min

1.5 mm double amplitude at frequency of 10 to 55 Hz in each X, Y, Z direction for 2 hours

500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times

Sunlight: ≤ 11,000 lx, incandescent lamp: ≤ 3,000 lx

-25 to 55 ℃, storage: -40 to 70 ℃ (no freezing or condensation)

35 to 85 %RH, storage: 35 to 85 %RH (no freezing or condensation)

IP65 (IEC standard)

Cable type

Ø 3.5 mm, 3-wire (emitter: 2-wire), 2 m

AWG24 (0.08 mm, 40-core), insulator outer diameter: Ø 1 mm

Case: PC+ABS, CAP: PC, sensing part: PMMA, bracket: SUS304, bolt: SCM, nut: SCM,

sleeve: Brass, Ni-plate

BJN□-NDT-□

Narrow beam

reflective

10 to 50

30 to 70

70 to 130

02)

03)

Opaque materials,

translucent materials

≥ Ø 0.2 mm

(copper wire)

≤ 25% of

≤ 20% of

sensing

distance

≤ 1 ms

Red

650 nm

≈ Ø 4.5

≈ Ø 2.0

≈ Ø 2.5

YES (Adjuster)

04)

YES

05)

ᜢ ᜽ ᜫ

≈ 45 g

or 30 mm

03)

01)