Autonics BS5-P Series 제품 설명서 - 페이지 3

{카테고리_이름} Autonics BS5-P Series에 대한 제품 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Autonics BS5-P Series 3 페이지. Push-button type photomicro sensors

페이지 인쇄

Specifications

Model

BS5-P1M□-□-□

Sensing type

Push button type

Button stop position

5.0 ± 0.4 mm

01)

Button output

4.0 ± 0.5 mm

switching position

01)

Button operation

≤ 0 mm

limit position

01)

Operation load

≤ 3 N

01)

Light source

Infrared LED

Peak emission

940 nm

wavelength

Emitter OFF

YES (External input

02)

Check stable operation YES (External input

02)

Operation mode

Light ON (Unpressed button, output ON) / Dark ON (Pressed button, output ON) mode model

Indicator

Operation indicator (red)

Approval

ᜢ ᜽ ᜫ

Unit weight (packaged) ≈ 30 g (≈ 50 g)

01)

Operation load

Pressure required from stop position

to output switching position

Stop position

Position of the button

without any applied pressure

Operation limit position

Position of the button

when fully pushed

02)

External input

NPN output

Short at 0 V or ≤ 0.25 VDCᜡ

Emitter OFF

(outflow current ≤ 30 mA)

Emitter ON

Open (leakage current ≤ 0.4 mA)

Response time

≤ 1 ms

Power supply

12-24 VDCᜡ ±10 % (ripple P-P: ≤ 10 %)

Current consumption

≤ 35 mA

Control output

NPN open collector output / PNP open collector output model

Load voltage

≤ 26.4 VDCᜡ

Load current

≤ 50 mA

Residual voltage

NPN: ≤ 1.5 VDCᜡ, PNP: ≤ 1.5 VDCᜡ

Protection circuit

Reverse power protection circuit, output short overcurrent protection circuit

Insulation resistance

≥ 20 MΩ (250 VDCᜡ megger)

Noise immunity

±240 VDCᜡ the square wave noise (pulse width: 1 ㎲) by the noise simulator

Dielectric strength

Between the charging part and the case: 1,000 VACᜠ at 50/60 Hz for 1 min

Vibration

1.5 mm double amplitude at 10 to 55 Hz frequency in each X, Y, Z direction for 2 hours

Shock

500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times

≥ 5,000,000 operations

Mechanical life cycle

(1 operation = stop position - operation limit position - stop position)

Ambient illumination

Fluorescent lamp: ≤ 1,000 lx

(receiver)

Ambient temperature

-20 to 55 ℃, storage: -25 to 70 ℃ (no freezing or condensation)

Ambient humidity

35 to 85 %RH, storage: 35 to 85 %RH (no freezing or condensation)

Protection rating

IP40 (IEC standard)

Connection method

Cable type

Cable spec.

Ø 3 mm, 4-wire, 1 m

Wire spec.

Refer to the specifications below depending on the models.

BS5-P1M□-□-□

AWG26 (0.08 mm, 30-core), insulator outer diameter: Ø 0.93 mm

BS5-P1M□-□-U

AWG26 (0.08 mm, 28-core), insulator outer diameter: Ø 0.9 mm

Material

Refer to the specifications below depending on the models.

BS5-P1M□-□-□

Case: PC + G, button: POM, sleeve: SUS304

BS5-P1M□-□-U

Case: PC, button: POM, sleeve: SUS304

BS5-P1M□-□-U

)

ᜢ ᜽ ᜨ

≈ 30 g (≈ 50 g)

Output switching position

Position where the output switches ON/OFF

PNP output

Short at +V or +V ≥ -0.25 VDCᜡ

(absortion current ≤ 30 mA)

Open (leakage current ≤ 0.4 mA)

18, Bansong-ro 513Beon-gil, Haeundae-gu, Busan, Republic of Korea, 48002