Galaxy Industries GLX PH-100 소유자 매뉴얼 - 페이지 2

{카테고리_이름} Galaxy Industries GLX PH-100에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Galaxy Industries GLX PH-100 2 페이지. Phase

페이지 인쇄

PH-100 PHASE

INSTRUCTIONS

Thanks for purchasing our product. In order to make the best use of your

PH-100, please read the following carefully.

FEATURES

The PH-100 offers a wide range of classic phasing effects, including Rise and

Fall phase.

BATTERY REPLACEMENT

1. Loosen the screw on the pedal to

open it.

2. Remove the battery from the

battery compartment and

disconnect the battery cable.

3. Connect a new battery to the

battery cable and put it back

in the battery compartment.

Make sure that the polarity

of the battery is correct and the

battery cable does not interfere with

the spring or pedal cover.

4. Push the coil spring into the spring

base and close the pedal.

5. Insert the thumb screw into the guide bush hole and ﬁrmly tighten the

screw.

IMPORTANT NOTES

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Do not use this apparatus near water.

5. Clean only with dry cloth.

6. Do not block any ventilation openings. Install in accordance with the

manufacturer's instructions.

7. Do not install near any heat sources such as radiators, heat registers,

stoves or any other apparatus (including ampliﬁers) that create heat.

8. WARNING: to reduce the risk of ﬁre or electric shock, do not expose this

apparatus to rain or moisture.

9. Protect the power cord from being walked on or being pinched.

10. Unplug this apparatus when unused for long periods of time.

11. There are no user serviceable parts inside. All servicing has to be done by

qualiﬁed service personnel. Servicing is required when the apparatus has

been damaged in any way, such as when the power supply cord or plug

is damaged, when liquid has been spilled or objects have fallen into the

apparatus, when the apparatus has been exposed to rain or moisture, when

the apparatus does not operate normally or when it has been dropped.

OWNER'S MANUAL

PANEL DESCRIPTION

1. AC Adaptor Jack: Connect an AC adaptor (100-140V/50-60Hz).

An AC adaptor allows long and secure operation without worrying about

battery life.

Use the proper supply for your area's Mains line voltage.

2. Indicator LED: This LED indicates when the effect is turned on.

•

Operating on battery power only: when the LED becomes dim or does

not light the battery needs to be replaced.

3. Rate Knob: Use this control to adjust the rate of the phase effect.

4. Depth Knob: Use this control to adjust the depth level of phase effect.

5. Res Knob: Used the Resonance control to adjust the strength of the ﬁlter

effect.

6. Mode Knob: Use this control to select aby of the following phase modes:

4 stage:

subtle depth phase

8 stage:

moderate depth phase

10 stage: strong depth phase

12 stage: maximum depth phase

Fall:

continuously falling phase effect

Rise:

continuously rising phase effect

7. Input Jack (MONO): Connect your instrument to this jack. To prolong bat-

tery life, disconnect all cables from the pedal when it's not in use.

8. Output Jack (MONO): Use these jack to connect an ampliﬁer or other

units.

9. Pedal: Press the pedal to turn the effect on and off

10. Thumb Screw: Loosen the screw to open the pedal for battery replacement.

(For details of the battery replacement, see "BATTERY REPLACEMENT")

SPECIFICATIONS

Input Impedance

Output impedance

Recommended Load

Impedance

Residual Noise

Power Supply

Connections

Controls

Indicator

Current draw

Dimensions

Weight

Option

1MΩ

1kΩ

10kΩ or greater

-90dBu (IHF-A, Typ.)

DC 9V; Dry Battery (6F22/9V), AC adaptor

Input, Output, AC Adaptor

Rate, Depth, Resonance, Mode

Check indicator (serves also

as battery check indicator)

55mA, (DC 9V)

72*128*60 mm.

415g (no battery)

AC adaptor

CONNECTIONS

1. Connecting an instrument to this jack will automatically switch the unit on.

Be sure to disconnect the cord from this jack when the unit is not being

used.

2. Before connecting or disconnecting any instrument, make sure that the

volume of the ampliﬁer is turned down.

3. The output jack is to connect an ampliﬁer or other units for mono use.

Both the dry and processed signals are output.