ADEO SCREEN FRAMEPRO 설치 매뉴얼 - 페이지 5

{카테고리_이름} ADEO SCREEN FRAMEPRO에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ADEO SCREEN FRAMEPRO 18 페이지. Fixed frame screen

ENGLISH - Fixed frame screen user manual

Screens and their projection surfaces are delicate and must be cleaned with great care, according to the following instructions:

Never use solvents, chemical or abrasive products, or pointed tools to clean the surface.

Avoid contact with other materials (varnishes, inks etc) as they might be impossible to remove from the canvas.

FABRIC VISION, REFERENCE, HELIOS: Remove dust from the case with a soft, clean cloth and a non aggressive detergent as necessary.

Clean the projection screen with a soft, clean, damp cloth, and a neutral or alcohol-base detergent as necessary. Since rubbing the screen with a cloth during cleaning operations can cause electrostatic

charge to accumulate, we recommend the subsequent application of an antistatic liquid with a clean cloth, to avoid dust being attracted again

GENERIC PROFILE: Remove dust from the case with a soft, clean cloth and a non aggressive detergent as necessary

VELVET PROFILE: Clean profile with a soft clean cloth, or a brush with soft, antistatic bristles. A vacuum-cleaner brush may be used, provided its bristles are soft and perfectly clean.

STRUCTURE and ANCHORING BRACKETS: The state of the product and the anchoring capacity of its brackets must be checked regularly. In case of canvas deformation or rips, or loosening of structural

components such as brackets or screws, action must be taken immediately to clear the area around the screen and avoid hazard to people and things, replace the defective component and restore the

product's functionality.

WARNING: When installing the screen use plugs and screws suitable for the screen's weight and for the type of wall or ceiling on which the mount brackets are to be fixed, based on the

following criteria

Screen width up to cm

Overall weight

See images on the end pages of this manual

First assemble the frame. Tighten the screws onto the angles as shown in figure 1.a and insert them into the lateral sections of the screen as indicated. In cases where the horizontal or vertical

sections are divided into two parts, insert the joint and join the profile sections together as shown in figure 1.b.

Then mount the screen according to the screen version purchased.

-"Rear elastics" canvas version: insert the metal rings (provided) into the lateral eyelets and secure the canvas with the elastics as shown in figure 2.a

-"Front elastics" canvas version: apply projection canvas angles with the double-sided adhesive provided, insert the metal rings into the eyelets and anchor the canvas with the elastics as shown in figure 2.b

-"Rear buttons" canvas version: secure the canvas with the buttons, starting from those placed on the corners of the frame, and subsequently using the sliders positioned on the aluminium sections, as

shown in figure 2.c.

-"Front buttons" canvas version: secure the canvas with the buttons positioned on the external side of the aluminium sections, as shown in figure 2.d.

Assembly with wall mount brackets is possible for screens up to 3m wide in the "rear elastics" version: mount the brackets onto the wall, recessed by 25cm on each side, as shown in figure 3.a; the

resulting screen assembly will be flush with the wall.

Assembly with spacers applies to screens from 3.5m to 7m wide, in the "rear elastics" version, and to all dimensions of the "front elastics" version. The number and arrangement of the spacers is

shown in figure 4: mount top and bottom spacers (where required) at a distance of 6cm from the outer edge of the aluminium section. Then loosely apply the nuts to the screws positioned on the

section. Secure the screws to the spacers and tighten the nuts with a wrench following the steps shown in figure 4.

First fix the collars to the screws of the angles or joints present on the aluminium frame, then secure the stands to the collars, as shown in figure 5.

As is the case for installation procedures, when the product reaches the end of its useful life, disposal operations must be carried out by qualified personnel.

The product is made up of various types of material: some can be recycled, others have to be disposed of. You must follow applicable recycling or disposal regulations in

force in your area for this product category.

As shown in the picture on the left, you must not throw the product into a domestic litter bin. Either dispose of the various components separately, pursuant to the

regulations applicable in your territory, or hand the product over to a vendor upon purchasing a similar new product.

Warning: local regulations can foresee heavy fines in case of unlawful disposal of this product.

1.GUARANTEE LIMITATIONS The Manufacturer guarantees that all the products it distributes are free of production-, material- and processing-related defects, without prejudice to the following terms and

conditions:

* The product is guaranteed for a period of twenty-four (24) months

* Mechanical parts are guaranteed for a period of thirty-six (36) months

* The motors and remote controls (excluding batteries) are guaranteed for a period of thirty-six (36) months

as from the date of the purchase invoice/receipt released to the end user

2.CONDITIONS AND LIMITATIONS This guarantee is subject to the following conditions and limitations:

the guarantee shall be deemed null and void if: the product has been used or manipulated in any manner other than those indicated in the user manual's instructions; or damaged as a result of improper use,

or owing to accident or negligence during transport; or if the product's defect is the result of repair or manhandling on the part of anyone other than personnel authorized by our Customer Care office.

The product must be installed by trained and experienced insider professionals, following the instructions provided for the installation and maintenance procedures.

3.RETURNS No product shall be returned and accepted without an authorization (RMA) released by Customer Care.

Products must be returned in their original (or equivalent) packaging to avoid being damaged during transport. Any transport damages resulting from inappropriate packaging shall not be covered by this

guarantee.

The returned product shall be accompanied by a detailed description of the defect and by a photocopy of the original purchase invoice/receipt.

The purchase invoice/receipt shall clearly indicate the following: Model – Serial number – Purchase date – Name and address of the purchaser and authorized dealer.

Made by Adeo Screen sp. Z o.o. (Polska) Specifications are subject to change without notice. E&OE

Doc: FRAMEPRO Installation Manual rev2 | 23.10.2012

Please verify that you are working with the latest revision of this document before specifying your screen.

06 CLEANING AND MAINTENANCE

07 INSTRUCTION FOR INSTALLATIONS

160

200

250

Kg 11

Kg 13

Kg 17

STAND INSTALLATIONS

PRODUCT'S DISPOSAL

GUARANTEE

300

360

400

500

Kg 22

Kg 27

Kg 32

Kg 43

600

700

Kg 53

Kg 63

Page 5