Autopage RST-1100 소유자 매뉴얼 - 페이지 13

{카테고리_이름} Autopage RST-1100에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Autopage RST-1100 20 페이지. Remote engine starter with alarm system

페이지 인쇄

long as you wish. To exit passive by-pass, press the transmitter

normal status.

G. ACTIVE DISARMING – UNLOCK & DISARM:

1. Press

button on the transmitter.

2. The siren will chirp twice and parking light flash twice to indicating that the security system is now

disarmed. The vehicle's door will unlock and dome light turns on for 30 seconds upon disarming when

interfaced with the security system.

TAMPER DISARMING: If alarm triggered, upon disarming the system, the siren will chirp 4 times and the

parking light will flash 3 times.

PATHWAY ILLUMINATION: This feature turns the parking lights "ON" for 30 seconds upon an unlock

signal and for 10 seconds upon the lock signal. (Programming required)

TWO STEPS DOOR UNLOCK: This feature will independently unlock the driver's door only when

disarming the security system. Pushing the

other doors. (Additional installation is required)

AUTOMATIC RE-ARM: If this feature is selected, the security system will automatically re-arm itself in 60

seconds after disarming with remote transmitter. Automatic rearm will cancel if the ignition is turned ON

and will pause if any door is opened before the 60 seconds timer has elapsed.

H. DISARMING WITHOUT A TRANSMITTER

OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE: (Factory Default Setting)

The Override function may be used if the remote transmitter is lost or inoperative.

1. Enter the vehicle and turn the ignition switch to 'ON' position. (Alarm will sound.)

2. Within 10 seconds push and release the valet switch

The alarm will stop sounding and enter the disarmed mode. You can now start and operate the vehicle

normally.

OVERRIDE THE ALARM WITH PASSWORD PIN CODE:

If the valet switch is located in a place that can be easily found, this security system allows the consumer to

program a password pin code offering a higher level of security.

1. Enter the vehicle and turn the ignition switch to the 'ON' position. (Alarm will sound.)

2. Within 5 seconds, enter your chosen the first digit code by pressing and releasing the Valet Switch.

(When you are finished with the above procedures, the system's siren stops alarming and the parking

lights stop flashing, but the vehicle cannot be started and driven away.)

3. If you use one digit to be a password pin code, skip to Step 6. If you use two digits to be a password pin

code, advance to Step 4.

4. Within 15 seconds of the last digit code enter (the 1st code), turn the Ignition Switch "Off" and then "On".

5. Within 15 seconds, enter your chosen of the second digit code by press and release the Valet Switch.

6. Turn the ignition switch to the "OFF" position. [4] Chirps form siren/horn, [3] flash from parking light to

indicate the system was disarmed.

Note: If someone keys-in the wrong password pin code, the system allows him to make 2 mistakes. If the

third code is still wrong, it will automatically shut down for 5 minutes. During this period the system

will not accept any code and the LED will "pause on" (the LED will turn on 1 second

and turn off 0.1 second).

EXAMPLE: To Override The System With The Password Code 83, you would;

1. Enter the vehicle and turn the ignition switch to 'ON' position. (Alarm will sound.)

2. Within 5 seconds, Press and Release the Valet Switch 8 times

(When finish the above procedure, the system's siren will stop alarming and the parking lights will stop

flashing, but the vehicle cannot be started and driven away.)

3. Within 15 seconds of the last digit code enter (the 1

4. Within 15 seconds, Press and Release the Valet Switch 3 times

RST1000 OP REV.A

SILENT DISARMING: Spin up the

then press the "Silent Disarm" button or press the transmitter

and

buttons at the same time to disarm your security

system, No chirp sound will be heard, arm and disarm

confirmation will be through the vehicles parking lights only.

button a second time within 3 seconds will unlock the

code), turn the Ignition Switch "Off" and then "ON".

button and the system will return to

switch to the page

Jun/22/2009

and