Autopage MA-200 운영 매뉴얼 - 페이지 5

{카테고리_이름} Autopage MA-200에 대한 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Autopage MA-200 13 페이지. 2-way remote control motorcycle alarm
Autopage MA-200에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (8 페이지)

페이지 인쇄

3. After the 30-second timer has elapsed, the security system will automatically "ARM". The siren will chirp

[1] time and the parking lights will flash [1] time.

PASSIVE ARMING BY-PASS: While the system is disarmed, press the

the security will respond with [1] chirp and LED will turn "ON". The security system will remain in this

temporary state for as long as you wish. To exit passive by-pass, press the

the system will return to normal status.

I. ACTIVE DISARMING –

1. Press the

button on the transmitter.

2. The siren will chirp twice and parking lights will flash twice to indicating that the security system is now

disarmed.

Activated on the

System Disarm

Tilt Sensor

(Optional)

Clearing the Flashing Icons: Pressing the

icons on the LCD screen transceiver.

SILENT DISARMING: Press the

security system. No chirp sound will be heard. Disarm confirmation will be through the motorcycles parking

lights only.

TAMPER DISARMING: If alarm has been triggered. Upon disarming the system the siren will chirp 4 times

and the parking lights will flash 3 times.

DISARMING WITH PATHWAY ILLUMINATION: Press the

will chirp once. Within 3 seconds, press

illuminate your pathway.

AUTOMATIC RE-ARM: If this feature is selected, the security system will automatically re-arm itself 60

seconds after disarming with remote transmitter. Pressing the

on the ignition switch will cancel the rearm.

J. DISARMING WITHOUT A TRANSMITTER

OVERRIDE THE ALARM WITHOUT PASSWORD PIN CODE: (Factory Default Setting)

The Override function may be used if the remote transmitter is lost or inoperative.

1. Turn the ignition switch to 'ON' position. (Alarm will sound.)

2. Within 10 seconds push and release the valet switch

The alarm will stop sounding and will enter the disarm mode. You can now start and operate the

motorcycle normally.

OVERRIDE THE ALARM WITH PASSWORD PIN CODE:

Since the valet switch can be easily found and defeated, this security system allows the consumer to

program a password pin code offering a higher level of security.

1. Turn the ignition switch to the 'ON' position. (Alarm will sound.)

2. Press the Valet switch the selected number of times (1-9 presses) within 15 seconds.

(By pressing the Valet switch the system's siren will stop alarming and the parking lights will stop

flashing but the motorcycle cannot be started and driven away until you disarm the system.)

The system should now be disarmed. If it is not, you may have waited too long to press the Valet switch;

turn the ignition off and on and try again.

K. VALET MODE:

(System in Disarm or Valet mode)

The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your

transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm

function are bypassed, however the remote panic feature and Channel 3 /4 will remain operational. To

use the valet mode, the system must first be disarmed either by using your remote transmitter, or by

operating the Manual override sequence.

MA-200 OP REV.A

Activated on the

Close Loop

Shock Sensor

button 3 times within 3 seconds will clear the flashing

button first, within 3 seconds press

button once to disarm the system, the siren

button. The parking lights will be turned "ON" for 30 seconds to

button twice within 3 seconds or turning

Oct/23/2006

button twice within 3 seconds,

button or

button and

Activated on the

Ignition Switch

button to silently disarm your