Dynatech V-5000 사용자 지침 - 페이지 6
{카테고리_이름} Dynatech V-5000에 대한 사용자 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Dynatech V-5000 16 페이지. Professional
페이지 인쇄
- 1. User Instructions
- 2. Table of Contents
- 3. Safety Precautions
- 4. Introduction
- 5. Front Panel
- 6. Rear Panels
- 7. Inputs
- 8. Outputs
- 9. Speakon Output Connector Assembly
- 10. Operating Modes
- 11. Limiter
- 12. Short Circuit Protection
- 13. Thermal Protection
- 14. Amplifier Features
- 15. Subwoofer and Speaker Setup
- 16. Specifications
13. Cooling Fans - Dual high speed cooling fans
14. Channel 2 Subwoofer Mode On/Off Switch - Turns the subwoofer
mode for channel two on and off.
15. Channel 2 Frequency Adjustment - This knob is used to adjust the
frequency level sent to your speaker on channel two when running the
channel in subwoofer mode.
16. Channel 1 Frequency Adjustment - This knob is used to adjust the
frequency level sent to your speaker on channel one when running the
channel in subwoofer mode.
17. Channel 1 Subwoofer Mode On/Off Switch - Turns the subwoofer
mode for channel one on and off.
18. Channel 2 XLR THRU Jack - This jack is used to send a parallel
signal from the channel two input jacks to another device or amplifier.
19. Mode Switch - This switch controls the amplifier's operating mode.
The amplifier can operate in three different modes; Mono Bridge, Parallel
Mono, or Stereo. The amplifier is shipped in stereo mode.
20. Channel 1 XLR THRU Jack - This jack is used to send a parallel
signal from the channel one input jacks to another device or amplifier.
21. Reset Button - This button is used to reset the breaker.
22. AC Cord - Plug this cable into a standard 230 V wall outlet.
13
14
15
16
17
30
29 28 27 26 25 24
Check that the voltage in your area matches the amplifiers required volt -
age. T o get optimum power out of this particular amplifier, switch the
standard Edison plug to a 30 amp. plug.
23. Channel 1 TRS Input - Channel one 1/4" female jack. Excepts either
a balanced or unbalanced plug. See page 7 for more details.
24. Channel 1 Output Jack/5 way Binding Post - Connect to your
speaker's input jack. Red is positive signal and Black is negative signal.
25. Channel 2 Output Jack/5 way Binding Post - Connect to your
speaker's input jack. Red is positive signal and Black is negative signal.
26. Channel 1 XLR input - Channel one 3-pin XLR balanced input jack.
See page 7 for more details.
27. Channel 1 Speakon Output - Optional speaker output connections.
Use pins 1+ and 1- of this 4-pole Speakon connector to connect to your
speaker's Speakon input jack.
28. Channel 2 XLR Input - Channel two 3-pin XLR balanced input jack.
See page 7 for more details.
29. Channel 2 Speakon Output - Optional speaker output connections.
Use pins 1+ and 1- of this 4-pole Speakon connector to connect to your
speaker's Speakon input jack.
30. Channel 2 TRS Input - Channel two 1/4" female jack. Excepts either
a balanced or unbalanced plug. See page 7 for more details.
page 6
18
19
20
21
PUSH TO RESET
~220V 50Hz
5800 WATTS
23
22
13
Diagram 2