Emerson APOLLO CF3900AW01 소유자 매뉴얼 - 페이지 8

{카테고리_이름} Emerson APOLLO CF3900AW01에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Emerson APOLLO CF3900AW01 13 페이지. 52" apollo series

페이지 인쇄

1. Attaching Light Kit

How to Wire Your

Ceiling Fan

If you feel that you do not have enough electrical

wiring knowledge or experience, have your fan

installed by a licensed electrician.

WARNING

To avoid possible electrical shock, be sure electricity

is turned off at the main fuse box before wiring.

NOTE: If you are not sure if the outlet box is ground-

ed, contact a licensed electrician for advice, as it

must be grounded for safe operation.

1. Connect the green grounding lead from the hanger

ball and the green grounding lead from the hanger

bracket to the grounding conductor of supply (this

may be a bare wire or wire with green colored insu-

lation). Securely connect wires with wire connector

supplied.

BLACK AND BLUE

FAN WIRES

GROUND

WIRE

CONNECTORS (3)

GREEN WIRE

(GROUND)

FROM FAN

GREEN WIRE

(GROUND)

FROM HANGER

BALL

Figure 4

NOTE: If you are using an Emerson Light Fixture

with your fan, see Light Fixture Owner's Manual

for wiring.

2. Securely connect the fan motor white wire to the

supply white (neutral) wire using wire connector

supplied (Figure 4). Securely connect the fan motor

black wire and blue wire to the supply black (hot)

wire using wire connector supplied (Figure 4). After

connections have been made, turn leads upward

and carefully push leads into the outlet box, with

the white and green leads on one side of the outlet

box and the black and blue leads on the other side

of the outlet box.

WARNING

Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire

connectors, except for the ground wire. Do not

operate fan until blades are in place. Noise and fan

damage could result.

3. Screw the two 1-1/4" threaded studs (provided) into

the tapped holes in the hanger bracket.

4. Lift the ceiling cover up to the threaded studs and

turn until studs protrude through the holes in the

ceiling cover (Figure 5).

5. Secure the ceiling cover in place by sliding lock-

Figure 5

WHITE SUPPLY

6. Slip the switch pull chain through the hole in the

(NEUTRAL)

WHITE FAN

WIRE

BLACK SUPPLY

(HOT)

1. Restore electrical power to the outlet box by turning

NOTE: CEILING COVER

OMITTED FOR CLARITY.

2. Check the operation of the fan by gently pulling on

3. If airflow is desired in opposite direction, turn your

THREE-SPEED

1st Pull—HIGH

2nd Pull—Medium

3rd Pull—Low

4th Pull—OFF

washers over the threaded studs and installing the

two knurled knobs (supplied). (Figure 5.) Tighten

the knurled knobs securely until the ceiling cover

fits snugly against the ceiling and the hole in the

ceiling cover is clear of the downrod. Your fan is

now wired to be turned on and off from the fan

switch.

1-1/4"

THREADED

STUD

KNURLED KNOB

WARNING

To avoid possible fire or shock, make sure that the

electrical wires are completely inside the outlet box

and not pinched between the ceiling cover and the

ceiling.

pendant (supplied), then secure the pendant by

snapping the coupling (supplied) onto the end of

the chain.

Using Your Ceiling Fan

the electricity on at the main fuse box.

the pull chain switch.

fan off and wait for the blades to stop turning, then

slide the reversing switch to opposite position, and

turn fan on again. The fan blades will turn in the

opposite direction and reverse the airflow.

Your fan model is equipped with a 4-position pull

chain switch. The operating sequence is as follows:

REVERSIBLE

SWITCH

CEILING COVER

LOCKWASHERS (2)

SPEED

CONTROL

SWITCH

AMERICA'S FAN COMPANY