Highlander iP-1Xinline 빠른 시작 매뉴얼 - 페이지 2

{카테고리_이름} Highlander iP-1Xinline에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Highlander iP-1Xinline 4 페이지. Pickup and preamp for single cone resophonic guitar pickup and preamp for single cone resophonic guitar

페이지 인쇄

iP-1Xinline INSTALL ATION

About External Power

As with any piezo pickup, it is important to have the preamplifier mounted as

close to the pickup as possible. This minimizes the length of cable between the

pickup and the preamp, greatly enhancing the sound quality.

The preamp requires a 9V battery. While Highlander systems can run for 1000

hours on one 9V battery, this battery will have to be replaced from time to time. In

an acoustic flat top guitar this is easily accomplished through the sound hole;

however, it is not so easy to access the inside of a resonator guitar. That is why

the External Power Accessory is highly recommended by Highlander and the

National Reso-Phonic Guitar Company. The cover plate on these guitars was not

designed to be removed and replaced regularly. Apart from the hassle, there is a

possibility that over time this could cause problems. The External Power Option

is easy to use, eliminating the hassle and potential problems.

The information and graphics contained in this document are the property of Highlander Musical Audio Products. Copying of any kind is prohibited, except for personal use only.

THIS INSTALL ATION SHOULD ONLY BE UNDER TAKEN BY LUTHIER WITH EXPERIENCE

T H I S I N S TA L L ATI O N S H O U L D O N LY B E U N D E R TA K E N B Y LU T H I E R W I T H E X P E R I E N C E

WORKING ON RESO-PHONIC STRINGED INSTRUMENTS.

Using the wrong techniques or tools could result in permanent damage to your Instrument.

Highlander is not responsible for any damage resulting from the installation of this pickup system.

Power is delivered to the guitar on the

'ring' of a stereo cable. If a mono cable is

inadvertently plugged into the guitar jack

on the External Power Box, the battery

will be shorted out. This will cause the

battery to run down very quickly, and

there is also the possibility that the

battery could get quite warm. If this

happens the battery should be replaced.

Please note the External Power Box is

used to power the preamp that is in the

guitar -- there is no preamplifier in the

External Power Box.

For optimum pickup performance and ease of installation, please take a

moment to read through this Installation Guide before beginning. Thank You.

Parts Included:

Qty. Description

Biscuit with Highlander Pickup embedded

iP-1Xi Inline Preamlifier

Hardware Mounting Kit comprising of:

Screws

Washers

Preamp Clamps

Male RCA Connector

Pieces of Self Adhesive Velcro® for cable strain relief

External Power Adapter comprising of:

External Power Box (battery not included)

15 foot Stereo Cable

Tools Required:

HAND DRILL or ELECTRIC DRILL (cordless preferred)

3/8" DRILL BIT, RELIEVED ON RAKE EDGES

Used for drilling guitar for the Output Connector

1/2" NUT DRIVER

For tightening

SHARP SCRIBER OR SIMILAR

For piercing the dome in the cone

SMALL SOLDERING IRON AND MULTICORE SOLDER

(must be electronic grade multicore solder not acid based)

For soldering the RCA Connector to the Pickup Cable

CROSS HEAD (PHILLIPS) SCREWDRIVER

For replacing the biscuit

WIRE CUTTERS

For trimming excess wire from the RCA Solder joins

MONO

CABLE

Audio

For more information check out our web site:

ighlanderpickups.com

Highlander Musical Audio Products 1991-2009