Gallien-Krueger Microbass MB150S/112 소유자 매뉴얼 - 페이지 3

{카테고리_이름} Gallien-Krueger Microbass MB150S/112에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Gallien-Krueger Microbass MB150S/112 12 페이지. Iii series
Gallien-Krueger Microbass MB150S/112에 대해서도 마찬가지입니다: 소유자 매뉴얼 (12 페이지)

페이지 인쇄
Gallien-Krueger Microbass MB150S/112 소유자 매뉴얼

Safety Information

Please read all enclosed safety precautions, be-
fore connecting or operating this product.
Verify Line Voltage and Amperage Before Use:
Your new MicroBass Series amplifier has been fac-
tory configured for use with:
· ·
120 Volt/60Hz 15 A circuit for USA/Canada.
230 Volt/50Hz 10 A circuit for UK/Australia.
· ·
240 Volt/50Hz 10 A circuit for Europe.
100 Volt/50Hz 15 A circuit for Japan.
·
220 Volt/50Hz 10 A circuit for Korea.
Connecting the amplifier to a line with specifications
other than indicated above can create a safety or fire
hazard and may damage the amplifier. If you have any
questions about the voltage requirements for your specific
model, or about the line voltage in your area, contact
your dealer before plugging the unit into a wall outlet.
Verify AC Circuit Capacity Before Use:
The high power output of your amplifier may require
heavy current draw under full-load conditions. To
insure proper performance and avoid potential safety
hazards, we recommend connection to line circuits with
amperage specified "as above". Connecting multiple
amplifiers to the same circuit, or connecting the am-
plifier to the same circuit used by other heavy-power
devices, such as high-wattage lights, may cause cir-
cuit breakers to trip. It is always a good idea to avoid
using any audio equipment on the same AC circuit as
equipment with motors, such as air conditioners or re-
frigerators. This will lessen the possibility of power
variation and electrical start-up noise affecting your
sound.
AC Power Cord:
To avoid safety hazards, use only the power cord
supplied with your unit. If a replacement cord is needed,
make certain that to use a standard IEC compliant
cord. Damaged power cords should be replaced im-
mediately.
MicroBass-III Series
Connecting to AC Power:
When setting up, make certain that the AC plug is easily
accessible. If mounting in a rack, ensure that the AC
mains can be easily disconnected by a plug or by an
all-pole disconnect switch on or near the rack.
Disconnect When Not In Use:
If you do not intend to use the amplifier for a consid-
erable length of time, disconnect the plug from the AC
outlet. Just switching the unit off does not mean that
it is fully disconnected from the AC Mains. To isolate
the unit from the AC mains, you must disconnect the
power cord from the unit and the AC outlet. When
disconnecting the power cord always pull from the
plug, never pull from the cord.
Do Not Open the Amplifier Enclosure:
There are no user-serviceable components inside this
product. Opening the amplifier enclosure may present
a shock hazard, and modification to the product will
void your warranty. If liquid enters the unit, or any
metal object such as a paper clip, wire, or staple ac-
cidentally falls inside the enclosure, disconnect the unit
from the AC power source immediately and consult
an authorized service station.
Unpacking:
The carton and packing materials used in shipping
your new amplifier were specifically designed to cushion
it from the shocks and vibration that occur during trans-
port. We suggest that you save the carton and pack-
ing materials for use in shipping, in the event you move,
or the amplifier needs repair.
3