Gallien-Krueger ML/S 사용 설명서 - 페이지 5

{카테고리_이름} Gallien-Krueger ML/S에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Gallien-Krueger ML/S 8 페이지. Micro lead series

SUGGESTED GALLIEN-KRUEGER SYSTEMS

Putting together the right system is as important to your final sound as choosing the right amplifier or the right guitar. Here are our favorite systems, each

designed to use all the power from the MicroLead, running at a total of 8 ohms per side stereo, or 4 ohms mono.

Combo systems are on the right, systems incorporating heads on the left. The size of your final system will depend largely on the portability you require.

Setting up your Sound

The ML/S and ML/E are capable of producing a wide range of great guitar

sounds. Below you will find the basic procedures needed to get started. We have

also provided several sample settings that can be used as starting points for various

guitar voicings.

Getting Started

LEAD CHANNEL

1) Set Channel select Switch (2) to "Lead".

2) Turn the volume and any tone controls on your guitar to "10" before making

adjustments on the ML/S or ML/E. These will be fine tuned later.

3) Set the Output Level (11) at the 2 o'clock position, the Gain Level (4) at the

10 o'clock position, the EQ at the 12o'clock position, and the Boost off (counter-

clockwise). While playing, set the Lead Master (4) to desired level.

4) Try the Shape (7) control to get a feel for how it alters the voicing of the Lead

channel. Set to achieve the desired starting sound.

5) You will find that the Equalization (10) is quite responsive and takes some trial

and error to get to know. From the flat (12 o'clock) position, take each control

one at a time and turn it all the way up and all the way off while laying your gui-

tar trough the unit. After you have become familiar with each one, set to the

desired position.

6) Before setting up any effects, adjust the Gain Level and set to the desired

amount of gain. The Gain Level will add saturation to the overdrive sound and

should be set before engaging any effects.

7) For the ML/E only : With your tone roughly set, familiarize yourself with both

the Reverb (24) and the Stereo Chorus (25-28) the same way as with the tone

controls. If you choose to use the effects, set to desired levels.

8) Try adjusting the Boost (3) in conjunction with the Gain Level. If you have the

footswitch hooked up, try footswitching the Boost on and off to explore the two

separate gain levels that can be achieved.

9) The final adjustment on the amplifier is the volume level. Turn up the Lead

Master (6) to your desired playing level.

10) Finally, fine tune your level and tone with adjustments on your guitar.

CLEAN CHANNEL

11) Set Channel Select Switch (2) to "CLN".

12) Repeat Step 2.

13) Set the Output Level (11) at the 2 o'clock position. Then while laying, set the

Volume (9) to desired playing level.

14) Repeat Step 5.

15) Repeat Step 7.

16) Try playing with the Compressor (23) on and off to hear the effect it creates.

17) The final adjustment on the amplifier is the volume level. Turn up the Volume

(9) to your desired playing level.

18) Finally, fine tune your level and tone with the adjustments on your guitar.

Note : Generally, keeping the Output Level greater than the 1 o'clock position

will avoid the problem of overdriving outboard effects.

Final note : Once the levels of each channel (Lead Master (6) and Volume(9))

have been set, use the Output Level (11) to control your overall stage level.

SAMPLE SETTINGS

• Controls shown in black are active or in the "in" position.

• Lead Master, Volume, and Output Level settings are dependant on speaker con

figuration, desired volume level, and outboard effects.

• Basic channel parameter settings on the ML/E shown below are intended to be

used with the ML/S as well.