Coram Showers OPTIMA 매뉴얼
{카테고리_이름} Coram Showers OPTIMA에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Coram Showers OPTIMA 2 페이지. Extender pack
Coram Showers OPTIMA에 대해서도 마찬가지입니다: 매뉴얼 (16 페이지), 매뉴얼 (2 페이지)
5
b
a
Side panel
Push-fit the top caps onto the wall channels and corner post.
6
50mm
Packaging:- The cardboard and polythene parts of this packaging can be recycled.
End of life:- This product contains materials such as aluminium and glass which can be recycled.
Please contact your local authority to find your nearest recycling centre.
IMPORTANT: You must not use the shower for 24 hours after installation of the enclosure.
DO NOT use bleach, scouring powders, solvents or other aggressive cleaning agents. To clean, use warm soapy water and a
clean cloth and rinse off.
Please note: There has been a glass coating applied to this product, use a squeegee to remove water and debris.
Periodically check all fixings and tighten if necessary.
CORAM SHOWERS LTD
Stanmore Industrial Estate, Bridgnorth, Shropshire WV15 5HP, UK • Tel: 01746 766466 • Fax: 01746 764140 • www.coram.co.uk
c
Door
From the outside only, apply
sealant to the bottom of the
enclosure and 50mm up the wall
channels and centre post as
shown.
Recycling
OPTIMA SIDE PANEL
DIMENSIONS
Check the enclosure size in
the table below matches the
showertray installation.
700 Panel Y = 670 - 695mm
760 Panel Y = 735 - 760mm
800 Panel Y = 775 - 800mm
900 Panel Y = 875 - 900mm
Please read these instructions carefully and keep for future reference.
Incorrect fitting will invalidate the guarantee.
SAFETY
● Handle glass with great care. Although the glass is very tough, sharp impacts can damage both the
glass and metal frame.
● Make sure there are no hidden pipes or cables hidden in the wall where you intend to drill.
● Wear safety goggles, shoes and appropriate clothing.
BEFORE INSTALLATION
● Check that the shower tray is level in all directions. The enclosure will not sit correctly on an uneven surface.
If uneven, the wall channels may not fit and the doors may not shut correctly.
● The enclosure should be fitted on tiled walls which are sealed with waterproof grout.
● There must be a good silicone seal between the rim of the shower tray and the wall.
● The shower tray and the enclosure must match in size. Attempting to fit the incorrect size of enclosure to
the shower tray will result in water leaks.
● Always check very carefully that components are vertical.
● To avoid damage, use the opened out packaging to build the enclosure on.
Equipment needed:
Drill, 6.5mm Masonry Bit, 4.5mm & 3mm Metal Bits (general), Crosshead Screwdriver, Spirit Level, Pencil, Tape Measure,
Masking Tape, Silicone Sealant.
Note: The screws and wall plugs supplied are for masonry walls. For lightweight walls i.e. stud partition, plasterboard etc,
use the correct type of fixings.
CUSTOMER CARELINE 01746 713410
00 71805 00 / Issue 1 / 15
DIMENSIONS
Check the enclosure size in
the table below matches the
showertray installation.
700 Door X = 653 - 703mm
760 Door X = 713 - 763mm
800 Door X = 753 - 803mm
900 Door X = 853 - 903mm
1000 Door X = 953 - 1003mm