maimin SABRE 3000 사용 설명서 및 부품 설명서 - 페이지 5
{카테고리_이름} maimin SABRE 3000에 대한 사용 설명서 및 부품 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. maimin SABRE 3000 20 페이지. Straight knife cutting machine with flexi-band sharpener
maimin SABRE 3000에 대해서도 마찬가지입니다: 지침 및 부품 목록 (12 페이지)
페이지 인쇄3.2
SHARPENER TROUBLE SHOOTING
Symptom
Possible
Gause
v
v
1.
No
bevel on one
side
of
blade.
2.
Sharpener runs
but
bands do
not rotate.
3.
Sharpener
does
not run but
bands
rotate.
4.
Sharpener
does
not run,
bands do
not rotate.
i
5.
Band
cut
offby
blade.
6.
Block (A397) falls off during
band changing.
7.
Block (A397)
pivots,
twisting
band.
8.
Sharpener runs slowly.
9.
Sharpener
overruns top position.
10.
Sharpener runs
continuously.
11.
Sharpener runs
only
when
Tripper
Handle
is
held.
12.
Sharpener jams.
13.
Presserfoot
Leg (,{403)
does
not
move
freely.
1.4.
Presserfoot
Lee
does
not hold.
15.
Safety
not working.
'16.
Bands
touch
bladp
in top position.
17.
Bevel
very
wide
on
both
sides
of
blade.
a)
Broken Torsion
Spring (4'382,
,4'388).
b) Band
Plates
(,4'381,
4387)
do
not
pivot
freely.
c) Bands do
not
cross
due
to interference of Band
Plates
(4381,
4387).
a) Square Shaft
Gear
(,{336)
broken.
b) Retaining Ring
(,4.338)
missing.
c)
Clamp
(A
364)
out of position.
a)
Keeper
Plate
(4'334)
loose.
b) Boat
(,4'333)
worn.
c)
Diamond
Shaft
(4356)
worn.
a) Presserfoot
Leg (Aa03) not down completely.
b) Oil
on
Crank
(,4505)
and/or Pulley
(.4.303).
c) Retaining Ring
(,4320) missing.
d) Cluster
Gear
(A332) broken.
a)
Band Plate
(4387)
defective.
a)
Retaining Ring
(,4398) missing.
a) Stud
(,4'383)
broken.
a)
Oil
on
Crank
(,4'505)
and/or Pulley
(4.303).
b)
Band Plate Guide
(4393)
too
tight
against
Standard (A56a).
c)
Worn
Pulley
(4303).
d)
Dirt
in Cartridge
(.4.318).
e)
Bent
Link
(A346).
f) Worn
Push
Rod
Cam (,4'314) and/or
Tripper
(4.350).
g)
Add
Grease
22174
to Band
Plate
Carrier
Gears
(4374).
a) Screw
(4363)
too low.
a) Soew
(,4'363)
too
low-les
than
l"above
Gear
Case
(A367).
a)
Pin
(,{348)
broken.
b) Worn
Push
Rod
Cam (4.314) and/or
Tripper
(,4.350).
a) Sharpener
run
without
knife in
machine.
b) Boat
(,4'333)
broken.
c)
Diamond
Shaft
(,4.356)
bent.
d)
Standard
(,4.564)
bent.
e)
Nylon Washer
(,4'3604')
broken.
a) Sharpener
not
at
top position.
b)
Dirt
in Leg Guide
(,4'354).
c)
Brake (A342) too
close
to
Pulley.
d)
Presserfoot
Leg
(,4.403)
bent.
a)
Lock
(,4'330)
loose on Shaft
(,4.325).
b)
Presserfoot
Handle
Spring
(4322)
broken.
c)
Teeth worn
on
Lock
(,4330).
d)
Screw
(4324)
loose.
a)
Leg Guide
(,4.354)
broken.
b)
Link
(,4.346)
bent.
a) Screw
(,4.363)
too high.
b)
Cams
(,4'515,
,4516)
too
high,
broken or
bent.
a)
Worn Band
Plates
(,4'387, ,4'381).
b) Band
Plate
Guide (4'393) too tight.
.\/