Dynojet Power commander V 설치 지침 매뉴얼 - 페이지 2

{카테고리_이름} Dynojet Power commander V에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dynojet Power commander V 6 페이지. 2017-2018 polaris scrambler 1000, 2017-2018 polaris sportsman 1000
Dynojet Power commander V에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (6 페이지), 설치 지침 매뉴얼 (9 페이지), 설치 지침 매뉴얼 (7 페이지), 설치 지침 (4 페이지), 설치 지침 (5 페이지), 설치 지침 (4 페이지), 설치 지침 (5 페이지), 설치 지침 (4 페이지), 설치 지침 (5 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 (5 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 (5 페이지), 설치 지침 (5 페이지), 설치 지침 (5 페이지), 설치 지침 매뉴얼 (7 페이지), 설치 지침 (5 페이지), 설치 지침 (4 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 (4 페이지), 설치 지침 (5 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 매뉴얼 (8 페이지), 설치 지침 (4 페이지), 설치 지침 매뉴얼 (7 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 매뉴얼 (8 페이지), 설치 지침 (4 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 (4 페이지), 설치 지침 (4 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 (5 페이지), 설치 지침 (5 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 매뉴얼 (7 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 (5 페이지), 설치 매뉴얼 (5 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 및 사용 설명서 (8 페이지), 설치 지침 및 사용 설명서 (6 페이지), 설치 매뉴얼 (4 페이지), 설치 매뉴얼 (7 페이지), 설치 매뉴얼 (6 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 (5 페이지), 설치 지침 (5 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 매뉴얼 (8 페이지), 설치 매뉴얼 (5 페이지), 설치 매뉴얼 (9 페이지), 설치 매뉴얼 (4 페이지), 설치 지침 (4 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 매뉴얼 (7 페이지), 설치 지침 매뉴얼 (7 페이지), 설치 지침 (5 페이지), 설치 지침 (7 페이지), 설치 지침 (4 페이지), 설치 지침 (4 페이지), 설치 지침 (5 페이지), 설치 지침 (5 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 (5 페이지), 설치 지침 매뉴얼 (5 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 매뉴얼 (7 페이지), 설치 지침 (4 페이지), 설치 지침 매뉴얼 (7 페이지), 설치 지침 (5 페이지), 설치 지침 (4 페이지), 설치 지침 (4 페이지), 설치 지침 (4 페이지), 설치 지침 (5 페이지), 설치 지침 (5 페이지), 설치 지침 (5 페이지), 설치 지침 (4 페이지), 설치 지침 (5 페이지), 설치 지침 (4 페이지), 설치 지침 (4 페이지), 설치 매뉴얼 (6 페이지), 설치 지침 (4 페이지), 설치 지침 (5 페이지), 설치 지침 매뉴얼 (7 페이지), 설치 지침 (4 페이지), 설치 지침 (5 페이지), 설치 지침 (5 페이지), 설치 매뉴얼 (6 페이지), 설치 지침 (4 페이지), 설치 지침 매뉴얼 (7 페이지), 설치 지침 매뉴얼 (6 페이지), 설치 지침 (4 페이지), 설치 지침 매뉴얼 (6 페이지)

Dynojet Power commander V 설치 지침 매뉴얼
POWER COMMANDER V
INPUT ACCESSORY GUIDE
USB CONNECTION
EXPANSION PORTS 1 & 2
Optional Accessories such as
POD-300 unit or Auto-tune kit.

Wire connections:

To input wires into the PCV first remove the rubber
plug on the backside of the unit and loosen the
screw for the corresponding input. Using a 22-24
gauge wire strip about 10mm from its end. Push the
wire into the hole of the PCV until is stops and then
tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make
inserting them easier.
15-042
www.powercommander.com

ACCESSORY INPUTS

Map -
Shifter-
N/A
ANALOG
SPEED
INPUT 2 (Grnd)
Speed-
INPUT 2
INPUT 1 (Grnd)
Analog-
INPUT 1
Launch-
(Input 1 or 2) The PCV has the ability to hold
2 different base maps. You can switch on the
fly between these two base maps when you
hook up a switch to the MAP inputs. You can
use any open/close type switch. The polarity
of the wires is not important. When using the
Autotune kit one position will hold a base map
and the other position will let you activate the
learning mode. When the switch is "CLOSED"
Autotune will be activated. (Set to Switch
Input #1 by default.)
(Input 1 or 2) Used for clutch-less full throttle
upshifts. Insert the wires from the Dynojet
quickshifter into either INPUT 1 or INPUT 2.
The polarity of the wires is not important. (Set
to Switch Input #2 by default.)
Not needed on Harley applications as the
speed signal wire is built into the main wiring
harness of the PCV.
This input is for a 0-5v signal such as
engine temp, boost, etc. Once this input
is established you can alter your fuel curve
based on this input in the control center
software.
You can connect a wire to either input 1 or
2 and then the other end to a switch. This
switch when engaged (continuity) will only
allow the RPM to be raised to a certain limit
(Set in the software). When released you will
have full RPM.
2017 Harley Davidson Touring PCV - 2