HIKOKI CV 14DBL 취급 지침 매뉴얼 - 페이지 7

{카테고리_이름} HIKOKI CV 14DBL에 대한 취급 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. HIKOKI CV 14DBL 16 페이지. Cordless multi tool

페이지 인쇄

NOTE

The recharging time may vary according to the ambient

temperature and power source voltage.

CAUTION

When the battery charger has been continuously used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next charging.

4. Disconnect the charger's power cord from the

receptacle.

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

CAUTION

○ If the battery is charged while it is heated because it has

been left for a long time in a location subject to direct

sunlight or because the battery has just been used, the

pilot lamp of UC18YFSL charger lights for 1 second,

does not light for 0.5 seconds (oﬀ for 0.5 seconds), or

the charge indicator lamp of UC18YSL3 charger lights

for 0.3 seconds, does not light for 0.3 seconds (oﬀ for 0.3

seconds). In such a case, ﬁ rst let the battery cool, then

start charging.

○ When the pilot lamp or charge indicator lamp ﬂ ickers (at

0.2-second intervals), check for and take out any foreign

objects in the charger's battery connector. If there are no

foreign objects, it is probable that the battery or charger

is malfunctioning. Take it to your authorized Service

Center.

○ Since the built-in micro computer takes about 3 seconds to

conﬁ rm that the battery being charged with charger is taken

out, wait for a minimum of 3 seconds before reinserting it

to continue charging. If the battery is reinserted within 3

seconds, the battery may not be properly charged.

○ If the pilot lamp or charge indicator lamp does not blink

in red (every second) even though the charger cord is

connected to the power, it indicates that the protection

circuit of the charger may be activated.

Remove the cord from the power and then connect

it again after 30 seconds or so. If this does not cause

the pilot lamp or charge indicator lamp to blink in red

(every second), please take the charger to the HiKOKI

Authorized Service Center.

MOUNTING AND OPERATION

Action

Removing and inserting the battery

Charging

Remaining battery indicator

How to use the LED light

Mounting the application tool

Switch Operation

Adjusting operating speed

Sawing

Sanding

Charging a USB device from an

electrical outlet

Charging a USB device and battery

from an electrical outlet

How to recharge USB device

When charging of USB device is

completed

Selecting accessories

Figure

11-a

11-b

―

The tool is equipped with two modes: "Standard Mode" and

"AUTO Mode".

(1) Standard Mode

You can change the vibration frequency between 6000

to 20000 /min by adjusting the dial from "1" to "5".

(2) AUTO Mode

Depending on the workload, AUTO Mode "A" will

automatically change the vibration frequency to 15000

/min or 20000 /min. This has the eﬀ ect of lowering

vibration and noise prior to and during operation.

Adjust the dial for the mode and speed that best suits your

task conditions and materials.

*1 Operating speed

Mode

Standard Mode

AUTO Mode

With AUTO Mode, the vibration frequency may not reach

20000 /min or return to 15000 /min depending on variables

such as the type of work or the attachment in use.

*2 Select accessories that are suited to a speciﬁ c task.

For details contact HiKOKI Authorized Service Center.

MAINTENANCE AND INSPECTION

1. Inspecting the application tool

Continued use of a dull or damaged application tool

will result in reduced cutting eﬃ ciency and may cause

overloading of the motor. Replace the application tool

with a new one as soon as excessive abrasion is noted.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very "heart" of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Cleaning on the outside

When the power tool is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use chloric

solvents, gasoline or paint thinner, for they melt plastics.

5. Storage

Store the power tool in a place in which the temperature

is less than 40°C and out of reach of children.

Page

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signiﬁ cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signiﬁ cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Dial

Vibration Frequency

1 – 5

6000 – 20000 /min

No load: 15000 /min

With load: 20000 /min