Dea ghost 200/24CL 사용 지침 및 경고 - 페이지 3

{카테고리_이름} Dea ghost 200/24CL에 대한 사용 지침 및 경고을 온라인으로 검색하거나 PDF를 다운로드하세요. Dea ghost 200/24CL 17 페이지. Underground electro-mechanical operator for swing gates
Dea ghost 200/24CL에 대해서도 마찬가지입니다: 사용 설명서 (16 페이지)

페이지 인쇄

Operating instructions and warnings

WARNING To ensure an appropriate level of electrical safety

always keep the 230V power supply cables apart (minimum

4mm in the open or 1 mm through insulation) from low volta-

ge cables (motors power supply, controls, electric locks, aerial

and auxiliary circuits power supply), and fasten the latter with

appropriate clamps near the terminal boards.

WARNING In line with EU Directive 2002/96/EC for waste

electrical and electronic equipment (WEEE), this electrical

product must not be disposed of as unsorted municipal waste.

Please dispose of this product by returning it to your local mu-

nicipal collection point for recycling.

3 MODELS AND CONTENTS

OF THE PACKAGE

The name GHOST 200 identifies a series of underground

electro-mechanical operators with different features depending

on motor phase power supply and speed.

DEA System articles in the series are listed in the "AVAILABLE

MODELS" table.

GHOST 200 is completed by a set of accessories listed in the

"PRODUCT ACCESSORIES" table.

Inspect the "Contents of the Package" on Page 30 and com-

pare it with your product for useful consultation during assembly.

4 OPERATING INSTRUCTIONS

In compliance with Directive 2006/42/CE Enclosure I, Point

1.7.4.

4.1 Product description

GHOST 200 is an electromechanical operator for swing ga-

tes (see F1, page 30) rotating an articulated arm.

This arm is connected to the gate to be operated by means of

the lever unit of the foundation box. The lever unit, that will be

properly welded at the time of installation, has a built-in opera-

tor unlocking device which will allow you to open the gate even

if there is a power supply failure.

4.2

Technical data

See the "TECHNICAL DATA" table.

4.3

Labelling information

Part of the summarised data for the CE label are listed in the

label applied to the product (see Position F7, Page 32); the data

regarding the seller are found in the enclosed Warranty, whi-

le "Indispensable Operating Safety Elements" are found under

Point "4.2 Technical data".

Motor power supply voltage (V)

Absorbed power (W)

Max torque (Nm)

Duty cycle (cycles/hour)

Maximum n° of operations in 24 hour

Built-in capacitor (µF)

Operating temperature range (°C)

Motor thermal protection (°C)

Opening time 90° (s)

Weight of product with package (Kg)

Protection degree

GH O ST 2 0 0

Article

Code

215

629000

215 I

629010

216

629020

218

629030

4.4

Appropriate conditions of use

The GHOST 200 is designed for installation in civil and indu-

strial swing gates as an actuator for the operational automatism

as shown in F3 on Page 31. By installing the accessory item 216

you may widen the wing angle of opening up to 180°.

The GHOST 200 has been designed and tested for opera-

tion under "normal" civil and industrial gate opening conditions;

temperature limits, degrees of protection against dust and water,

and other data are provided in Point 4.2 "Technical Data".

Satisfactory operation requires the correct positioning of

the GHOST 200 operator with respect to the gate (see F4 page

30).

The required automation must be selected according to the

gate to be moved; the attrition on the attachments, the weight,

the length/height of the gate wing, and the degree of closing

of the surfaces are the elements to be considered. The chart

"LENGTH-WEIGHT" correlating the length of the gate leaf and

its weight in typical situations can be used in selecting the auto-

mation according to the gate to be automated.

200 - 200CL - 200/EN - 200/CLEN

230 V ~ ±10% (50/60 Hz)

400

320

20 - 28

(200/EN)

200

12,5

150 °C

14,5

"PRODUCT ACCESSORIES" table

Description

Zinc-plated foun-

dation box with

release device

Stainless steel

foundation box with

release device

Device to be in-

stalled on item art.

215 and 215I to

get a 180° angle of

opening

Mechanical stop

200L

200/24 - 200/24CL

24 V

330

300

200

-20÷50 °C

IP67

150

210

280