HIKOKI M 18DYA 취급 지침 매뉴얼 - 페이지 10

{카테고리_이름} HIKOKI M 18DYA에 대한 취급 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. HIKOKI M 18DYA 16 페이지.

페이지 인쇄

English

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the

accessories listed on page 13.

Standard accessories are subject to change without notice.

APPLICATIONS

○ Window-removing and cutting of gypsum board

SPECIFICATIONS

Model

Voltage

No-Load Speed

Collet chuck capacity

Weight

NOTE

Due to HiKOKI's continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

Electronic control

○ Restart prevention function

When the power is still switched on, the tool will not

restart when a battery is installed. This function can be

canceled once the tool is switched oﬀ .

NOTE

If left unattended with the restart prevention activated,

the battery will be depleted.

○ Braking Function

Brake is activated when the switch is turned oﬀ , stopping

the motor's rotation.

CHARGING

Before using the power tool, charge the battery as follows.

1. Connect the charger's power cord to the receptacle.

When connecting the plug of the charger to a receptacle,

the pilot lamp will blink in red (At 1- second intervals).

2. Insert the battery into the charger.

Firmly insert the battery into the charger as shown in

Fig. 4 (on page 3).

3. Charging

When inserting a battery in the charger, charging will

commence and the pilot lamp will light continuously in

red.

When the battery becomes fully recharged, the pilot lamp

will blink in red. (At 1-second intervals) (See Table 1)

● Pilot lamp indication

The indications of the pilot lamp will be as shown in

Table 1, according to the condition of the charger or the

rechargeable battery.

M18DYA

18 V

28000 /min

1/8" or 1/4"

1.1 kg (BSL1820M)

Indications of the pilot lamp (RED)

Lights on for

0.5 seconds and oﬀ

Before

for 0.5 seconds

charging

Blinks

Lights continuously

While

Lights

charging

Lights on for

0.5 seconds and oﬀ

Charging

for 0.5 seconds

complete

Blinks

Lights on for

1 second and oﬀ for

Overheat

0.5 seconds

standby

Blinks

Lights on for

0.1 seconds and oﬀ

Charging

for 0.1 seconds

impossible

Flickers

● Regarding the temperatures and charging time of the

battery.

The temperatures and charging time will become as

shown in Table 2

Battery

Charging voltage

Weight

Temperatures at which the battery

can be recharged

Charging time for battery capacity,

approx. (At 20°C)

1.5 Ah

2.0 Ah

2.5 Ah

3.0 Ah

4.0 Ah

5.0 Ah

6.0 Ah

8.0 Ah

Number of battery cells

NOTE

The recharging time may vary according to the ambient

temperature and power source voltage.

CAUTION

When the battery charger has been continuously used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next charging.

4. Disconnect the charger's power cord from the

receptacle.

5. Hold the charger ﬁ rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

Table 1

Plugged into power

source

—

Battery overheated.

Unable to charge.

(Charging will

commence when

battery cools)

Malfunction in

the battery or the

charger

Table 2

Charger

UC18YFSL

14.4–18

0.5

0°C–50°C

min

120

4–10