Corbin Russwin DC8200 Series 설치 지침 매뉴얼 - 페이지 8

{카테고리_이름} Corbin Russwin DC8200 Series에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Corbin Russwin DC8200 Series 8 페이지. Multi-sized 1 thru 6

페이지 인쇄

DC8000 Installation Instructions - Closer Adjustment

Spring Power Adjustment

Locate spring power adjuster from Illustration below

DC8200 Size 1 thru 6 Adjustment See Chart

DC8200 SPRING POWER ADJUSTMENT CHART

All DC8200 closers are factory set at an approximate

Adjust closer as necessary for door size using this chart.

Readjustment may be required to suit prevailing conditions.

Date Stamp

(on end of closer)

MM-YY

MM = Month

YY = Year

Option

M-71

Closing Speed Valve

To adjust speed of door closing from fully open to a position

2 to 5 from closed, turn Closing Speed Valve CLOCKWISE

to SLOW closing, COUNTER-CLOCKWISE to SPEED

closing.

Latching Speed Valve

After closing speed has been obtained, turn latching speed valve

CLOCKWISE to SLOW latching or COUNTER-CLOCKWISE to

SPEED latching for last 2 to 5 of door travel.

NOTE: Set combination of CLOSING and LATCHING speeds to

between 3 and 7 seconds Use of door by handicapped,

elderly or small children may require even greater

closing time.

Delayed Action Valve

Turn valve CLOCKWISE to SLOW closing, COUNTER-

CLOCKWISE to SPEED closing. Delayed action may be

adjusted from 20 seconds to 90 seconds, depending on

degree of door swing. Delay occurs at the beginning of the

door closing cycle from fully open down to 70°, where the

closing speed valve then begins its control.

80-9380-8000-152 Rev. 09/06

Size 3.

LATCHING

SPEED VALVE

OPTION M71

DELAYED

ACTION VALVE

(1/8 Allen Wrench Provided)

DIAL

Size of Door

Interior Exterior

Swing

' "

2 4 (712)

2 6 (764)

' "

2 6 (764)

3 0 (915)

' "

3 0 (915)

3 6 (1067)

' "

3 6 (1067)

4 0 (1219)

CLOSING

SPEED VALVE

Backcheck Intensity Valve

Turn valve COUNTER-CLOCKWISE to reduce backcheck

or CLOCKWISE to increase backcheck. (Backcheck should

be set to give a soft cushioning action, not a sudden stop.)

Installing Cover

Slip cover over closer.

Hold tightly against QUIK-INSTALL® Bracket surface.

Secure on each side with 6-32 x 1/4 PBHMS screws.

Insert is removable.

Place in unused opening.

To Adjust Hold Open (A1 Option)

Open the door to desired position and tighten the hold open

screw firmly (For RH application, turn screw on underside

CLOCKWISE. For LH application, turn screw COUNTER-

CLOCKWISE.) Place the hold open dial over the hex head

of the bracket screw so that one of the slots in the dial is

directly over small screw hole tapped in bracket. Seat the

dial tightly over the bracket. INSERT DIAL SCREW AND

TIGHTEN SECURELY.

HOLD OPEN

SCREW

Spring Power Adjustment

No. Full Turns Clockwise

Exterior

Out

Regular &

Parallel Arm

Swing

TJ Mounting

Mounting

1-5

2-7

5-8

7-11

' "

8-13

11-15

2 6 (764)

' "

13-15

15-17

3 0 (915)

BACKCHECK

INTENSITY VALVE

SPRING POWER ADJUSTER

(1/4 ALLEN WRENCH)

Plastic Cover

(Standard)

Equivalent

Closer Size

(Approx.)

DIAL

SCREW