Airetool EIC-625-1000 운영 및 서비스 매뉴얼 - 페이지 3

{카테고리_이름} Airetool EIC-625-1000에 대한 운영 및 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Airetool EIC-625-1000 16 페이지. Tube cutters

페이지 인쇄

Safety Recommendations

repetitive motions and/or vibrations. Those individuals pre-

disposed to vasculatory or circulatory problems may be

particularly susceptible. Cumulative trauma disorders such

as carpal tunnel syndrome and tendonitis can be caused

or aggravated by repetitious, forceful exertions of the hands

and arms. These disorders develop gradually over periods

of weeks, months, and years.

TASKS SHOULD BE PERFORMED IN SUCH A MANNER

THAT THE WRISTS ARE MAINTAINED IN A NEUTRAL

POSITION WHICH IS NOT FLEXED, HYPEREXTENDED,

OR TURNED SIDE TO SIDE.

STRESSFUL POSTURES SHOULD BE AVOIDED AND

CAN BE CONTROLLED THROUGH TOOL SELECTION

AND WORK LOCATION.

Any user suffering from prolonged symptoms of tingling,

numbness, blanching of the fingers, clumsiness or weak-

ened grip, nocturnal pain in the hand, or any other disorder

of the shoulders, arms, wrists, or fingers is advised to con-

sult with a physician. If it is determined that the symptoms

are job related or aggravated by movements and postures

dictated by the job design, it may be necessary for the

employer to take steps to prevent further occurrences. These

steps might include, but are not limited to, repositioning

the work piece or redesigning the workstation, reassigning

workers to other jobs, rotating jobs, altering work pace,

and/or changing the type of tool used so as to minimize

stress on the operator. Some tasks may require more than

one type of tool to obtain the optimum operator/tool/task

relationship.

The following recommendations will help reduce or mod-

erate the effects of repetitive work motions :

•

Use a minimum hand grip force consistent with

proper control and safe operation.

•

Keep wrists as straight as possible.

•

Keep body and hands warm and dry.

•

Avoid anything that inhibits blood

circulation

- Smoking tobacco

- Cold temperatures

- Certain drugs

•

Avoid highly repetitive movements of the

hands and wrists, and continuous vibration

exposure.

Use of this tool may produce hazardous fumes, particles,

and/or dust. To avoid adverse health effects utilize adequate

ventilation and/or a respirator. Read the material safety data

sheet of any materials involved in the tube expansion pro-

cess.

This Airetool product is designed to operate on minimum

90 psig ( 6.2 bar ), maximum 125 psig ( 8.6 ) air pressure.

If the tool is properly sized and applied, higher air pressure

is unnecessary. Excessive air pressure increases the loads

and stresses on the tool parts, mandrels, rolls and cages

and may result in premature wear and or breakage. Instal-

lation of a filter-regulator-lubricator in the air supply line

ahead of the tool is required.

Before the tool is connected to the air supply, check the

throttle for proper operation ( i.e., the throttle moves freely

and returns to the closed "OFF" position when released ).

Clear the air hose of accumulated dust and moisture. Be

careful not to endanger adjacent personnel. Before remov-

ing a tool from service or changing sockets, make sure the

air line is shut off and drained of air. This will prevent the

tool from operating if the throttle is accidently engaged.

It is essential for safe operation that any operator of an

Airetrol use good balance, sure footing, and proper posture

in anticipation of a torque reaction. Ensure that the

operator's hands will not be wedged or pinched between

the work and the tool when operating.

NOTE : ANY USE OF THIS TOOL OTHER THAN IT'S

INTENDED PURPOSE COULD CAUSE MAJOR DAM-

AGE TO THE TOOL AS WELL AS POSE A RISK TO

THE OPERATOR.

Page - 3