Majestic fireplaces VF Collection UVS36 주택 소유자 설치 및 운영 매뉴얼 - 페이지 11

{카테고리_이름} Majestic fireplaces VF Collection UVS36에 대한 주택 소유자 설치 및 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Majestic fireplaces VF Collection UVS36 20 페이지. The vf collection vent-free gas fireplaces
Majestic fireplaces VF Collection UVS36에 대해서도 마찬가지입니다: 사양 (2 페이지)

페이지 인쇄

7. Place top left log (BE9 or BF11) onto locator notches.

Ensure log is secure.

8. Place top right log (BE10 or BF12) onto locator

notches. Ensure log is secure.

BE9

BE6

Fig. 14 UVC/UVS36 log placement.

BF10

BF8

Fig. 15 UVC/UVS43 log placement.

Ember Material Placement

LG132

Separate the ember material into small pieces and

UVC/UVS43

place onto the burner in front of the front logs. Do NOT

Log placement

pack down, leave in ﬂuffy, loose condition for most re-

9/8/00 djt

alistic ember effects. Do not install more embers on

the burner than come with the unit.

Application of excess loose material may adversely

affect performance of theheater.

Replacement loose embers must be purchased

through authorized Majestic Fireplaces dealers.

WARNING: All previously applied loose

material must be removed prior to reappli-

cation.

Lava Rock

The lava rock provided with this ﬁreplace must be

placed on the ﬁrebox bottom on either side of the

burner assembly. Do not place lava rock in combustion

pan.

Under no circumstances should this lava

rock be placed on any part of the burner

assembly.

Flame Adjustment

For ﬁreplaces equipped with HI/LO valves, ﬂame ad-

justment is accomplished by rotating the HI/LO adjust-

ment knob located near the center of the gas control.

(Fig. 16)

20000135

BE10

BF11

LG131

UVC/UVS36 LOGS

9/8/00 djt

Majestic Fireplaces

Turn

counterclockwise

to decrease

flame height

BE8

Fig. 16 Flame adjustment knob for Honeywell Valve.

BE7

It is important to periodically perform a visual check

of the pilot and burner ﬂames. Compare them to the

Figures 17 or 18. If the ﬂame patterns appear abnor-

mal, contact a qualiﬁed service provider for service and

LG131

adjustment.

BF12

BF9

Fig. 17 Correct pilot ﬂame pattern.

LG132

UVC36/UVS43

UVC43/UVS43

Fig. 18 Approximate ﬂame heights for each model.

Upon completing the gas line connection, a small

amount of air will be in the lines. When ﬁrst lighting unit

with pilot light, it will take a few minutes to purge them-

selves of this air. Once the purging is complete, the

pilot and burner will light and operate as indicated in the

instruction manual. Subsequent lightings of the heater

will not require such purging.

When lit for the ﬁrst time, the appliance will emit a slight

odor for awhile. This is due to paint and lubricants used

in the manufacturing process. After each lighting, vapor

may condense and fog the glass; this moisture disap-

pears within a few minutes of burning.

UVC / UVS Vent-Free Heaters

Flame Characteristics

HV102

Honeywell hi/lo knob

4/5/99 djt

IF449

NOVA SIT PILOT

UVC

2/14/97

LG131

UVC/UVS36 LOGS

9/8/00 djt

First Firing

LG134

UVC/UVS43

Log placement flames

9/8/00 djt

Turn clockwise

to increase

flame height

FP449

LG133

LG134