AFRISO 13 384 20 매뉴얼 - 페이지 2

{카테고리_이름} AFRISO 13 384 20에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. AFRISO 13 384 20 6 페이지. 3-way rotary mixing valves

OPERATION OF THE VALVE

1. Position of the knob with scale

Once the valve has been correctly set and the scale was selected, position "0" will mean that the valve is fully closed

(hot water supply is closed) and position "10" will mean the valve is fully open (hot water supply is open). Any other

position on the scale will indicate the percentage of valve opening (e.g. position "4" will mean the valve is 40% open).

Fig. 3. Position of dial with scale

2. Position of closing element

The closing element is located on the opposite side of the flattening on the adapter. To check the correct operation

of the valve, remove the knob from the adapter and check the location of the flattening.

Fig. 4. Closing element position

TECHNICAL DATA

Parameter/part

Operating temperature

Operating pressure

Differential pressure

Kvs coefficient in a mixing function

Internal leakage as a function of mixing (% of maximal

Kvs value valve)

Kvs coefficient in switching/diverting function

Internal leakage in the switching/diverting function (%

of maximal Kvs value valve)

Required torque

Swivel angle

Glycol concentration

Material

Mixing function

Value/material

5-95°C

max 10 bar

max 1 bar

DN20: 3.5 - 9 m³/h

DN25: 4.5 - 12 m³/h

DN32: 7.5 - 19 m³/h

DN40: 14 - 36 m³/h

DN50: 17 - 50 m³/h

DN20: < 0,1 % at Δp=50kPa; <0,2% at Δp=100kPa

DN25: < 0.2 % at Δp=50kPa; <0,2% at Δp=100kPa

DN32: < 0.3 % at Δp=50kPa; <0,7% at Δp=100kPa

DN40: < 0.7 % at Δp=100kPa

DN50: < 0.7 % at Δp=100kPa

With the flow straight ahead:

DN20: 9 m³/h

DN25: 12 m³/h

DN32: 19 m³/h

DN40: 36 m³/h

DN50: 50 m³/h

With a flow at 90°:

DN20: 3,4 m³/h

DN25: 5,4 m³/h

DN32: 9,8 m³/h

DN40: 16,2 m³/h

DN50: 24 m³/h

DN20 – DN32: <0,05%

DN40 – DN50: <0,2%

DN20 – DN32: <0,5 Nm

DN40 – DN50: <2,5 Nm

90°

max 50%

Brass, plastic

3. Installation of the ProClick electric actuator or controller

Under the knob of the ARV Vario ProClick valve, there is always an adapter for mounting the ProClick electric actuator

or the controller. With the ProClick mounting system (fig. 5), simply remove the knob and blue limiting ring from

the valve and then slide the ProClick actuator or controller into position until the mounting mechanism engages

on the valve. When using the valve in the mixing function, ACT/ARC ProClick controller or a 3-point actuator must

be used (e.g. AFRISO ARM 343 ProClick). In order to automate the valve in the switching function, a 2-point actuator

(e.g. AFRISO ARM 703 ProClick) must be used.

APPROVALS AND CERTIFICATES

ARV Vario ProClick 3-way rotary mixing valves are subject to the Pressure Directive 2014/ 6 8/EU and are not CE marked

in accordance with Article 4.3 (recognised engineering practice).

The products have been marked with the B construction mark, in accordance with the regulations in force in Poland.

MAITENANCE

ARV Vario ProClick 3-way rotary mixing valves require no maintenance.

DECOMMISSIONING, DISPOSAL

1. Dismantle the device.

2. In the interest of environmental protection, the decommissioned appliance must not be disposed of with

unsorted household waste. The device must be taken to a suitable disposal centre.

ARV Vario ProClick 3-way rotary mixing valves are built from recyclable materials.

WARRANTY

Product guarantee in accordance with the general conditions of sale and delivery.

CUSTOMER SATISFACTION

For AFRISO customer satisfaction is paramount. If you have any questions, suggestions or product problems,

please contact us.

page

Fig. 5. ProClick system