KitchenAid 36" 설치 지침 - 페이지 4

{카테고리_이름} KitchenAid 36"에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid 36" 5 페이지. 30” and 36” gas sealed burner glass cooktops
KitchenAid 36"에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (16 페이지)

페이지 인쇄

Use a brush and liquid detergent to

test all gas connections for leaks.

Bubbles around connections

will

indicate a leak. If a leak appears, shut

off gas valve controls and adjust connections.

Then

check connections

again. NEVER TEST FOR GAS

LEAKS WITH A MATCH OR OTHER FLAME.

Clean all detergent solution from cooktop.

Plug the power

supply cord into

the grounded

outlet.

Numbers

correspond to

steps.

F-l

Place burner

grates over

burners and

caps. Install

on valve stems.

i cooktop

countertop

glass

control knobs

Electronic Ignition System-

initial lighting

Cooktop burners use electronic igniters in place of

standing pilots. When the cooktop control knob is

turned to the "HI" position, the system creates a

spark to light the burner. This sparking continues

until the burner ignites.

l-a-l

If the depth of your cutout

19-l/2"

or less, go to Step 5.

- - 1 If the depth of your cutout

is larger

than 19-l/2",

insert four,

l-1/4"

centering screws in

the holes on the front and back of the cooktop burner

box. Measure the distance from the penciled outline

on the countertop to the edge of the cutout. Mark the

same distance on the underside of the cooktop from

the edge in toward the rear centering screws. Adjust

the rear centering screws to the marks. Do Not

adjust the front centering screws at this time.

q 8

Rotate mounting brackets away from

burner box. Tighten the mounting

brackets to the burner box. Insert the

2-l/2" clamping screws into the

mounting brackets. Use a screwdriver to tighten

screws against the underside of countertop.

Remove pencil outline from countertop.

116.

Check the

operation of

the cooktop

burners. Push in and turn

each control knob to "HI"

position.

The flame should

light within 4 seconds.

If burners do not light

properly, turn control knob

to the "OFF' position.

Check that burner cap is in

Install the pressure regulator with the

arrow on the regulator pointing up

toward unit and in a position where

you can reach the access cap.

the proper position. Check that power supply cord

is plugged in and that the circuit breaker or house

fuse has not blown. Check that the shutoff valve is

in the "ON" position. Check operation again.

If a

burner does not light at this point, contact your

KitchenAid dealer for assistance.

Fire Hazard

Do Not make connection

too tight.

The

regulator

is die cast.

Over-tightening

may crack regulator

resulting

in a gas leak and possible

fire or

explosion.

Ll 5

Remove the paper backing from a small

section of the foam sealing strip. Place

the strip l/8" from cooktop edge on the

underside of the glass. Continue until

foam strip completely

outlines the edge of the

cooktop. Do Not use additional sealant around outer

edge of cooktop.

v-l

Check each cooktop

burner for proper flame.

The small inner cone

318"

nipple

should have a very

distinct blue flame approximately

l/2"

long. The outer cone is not as distinct

as the inner cone.

318"

adapters /

manual shutoff valve

pressure

regulator

Push in and turn each control knob to

the "LO" (or simmer) setting. The

"LO" setting of each burner has been

factory set to the lowest setting

available to provide reliable reignition of the burner.

If it does not stay lit on the "LO" setting, contact

your KitchenAid dealer for assistance.

All connections

must be wrench-tightened.

Assemble the flexible connector

from the gas supply pipe to the

oressure reaulator in order:

'manual shuToff valve, 3/8" nipple,

318" adapter, flexible connector, 318" adapter,

and 318" nipple.

Attach the mounting brackets to each

side of the burner box with the 5/l 6"

screws. Do Not tighten the screws. Turn

the mounting brackets so each is under

the burner box.

Use pipe-joint compound made for

use with NATURAL and L.P. gas

to seal all gas connections.

flexible connectors are used, be

certain connectors are not kinked.

To get the most efficient use

from your new cooktop, read

your KitchenAid Use and Care

Guide. Keep Installation

Instructions

and Guide close to

cooktop for easy reference.

Insert cook-top into cutout and align with

pencil outline. Check that cooktop is

parallel to front edge of countertop. Lift

entire cooktop to make adjustments

the foam sealing strip can seal properly. If you used

centering screws, adjust the front centering screws

until cooktop is held tightly in the cabinet.

Open the shutoff valve in the gas

supply line. Wait a few minutes for

gas to move through the gas line.

L.P. gas

conversion

No attempt shall be made to convert the appliance

from the gas specified on the seriavrating

plate for

use with a different gas without consulting the

servicing gas supplier.

Conversion

must be done by

a service technician.

Conversion

Kit No. 4175385 is

available from your KitchenAid dealer or authorized

parts distributor.

Fire Hazard

Do Not overtighten

screws.

Over-tightening

screws could damage

cooMop

surface.

Fire Hazard

Do Not use an open flame to test for leaks

from gas connections.

Checking

for leaks with a flame may result in

a fire or explosion.

Panel C