KitchenAid GCI3061XB 설치 지침 매뉴얼 - 페이지 3

{카테고리_이름} KitchenAid GCI3061XB에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid GCI3061XB 12 페이지. 30" (76.2 cm) electric induction cooktop

페이지 인쇄

Cabinet Dimensions

IMPORTANT: If installing a range hood or microwave hood

combination above the range, follow the range hood or

microwave hood combination installation instructions for

dimensional clearances above the cooktop surface.

A. 29½" (75.0 cm) on 30" (76.2 cm) models

B. Combustible area above countertop (shown by dashed box above)

C. 30" (76.2 cm) minimum clearance between top of cooktop platform

and bottom of uncovered wood or metal cabinet (24" [61 cm]

minimum clearance if bottom of wood or metal cabinet is covered

by not less than

" [0.6 cm] flame retardant millboard covered with

not less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless

steel, or 0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper)

D. 13" (33.0 cm) recommended upper cabinet depth

E. 2" (5.1 cm)

F. 19

" (49.0 cm)

G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop

within minimum horizontal clearances to cooktop

H. Junction box or outlet; 12" (30.5 cm) minimum from bottom of

countertop

I. Junction box or outlet; 10" (25.4 cm) from right-hand side of

cabinet

J. 29½" (75.0 cm) on 30" (76.2 cm) models

K. 1" (2.5 cm) minimum distance to nearest left and right side

combustible surface above cooktop

L. 1" (2.5 cm) minimum clearance between back wall and countertop

M. IMPORTANT: For proper ventilation, provide a vent of

under the countertop, in the front of the cabinet. The ventilation

opening is to extend the full length of the cooktop cutout. See

following illustration.

(5.0 mm)

NOTES: After you make the countertop cutout, some installations

may require notching down the base cabinet side walls to clear

the cooktop base. To avoid this modification, use a base cabinet

with sidewalls wider than the cutout.

" (5 mm)

If cabinet has a drawer, a 5 " (13 cm) depth clearance from the

countertop to the top of the drawer (or other obstruction) in base

cabinet is required.

Electrical Requirements

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge copper wire.

Electrically ground cooktop.

Failure to follow these instructions can result in death,

fire, or electrical shock.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path and wire gauge are in accordance with local

codes.

Check with a qualified electrical installer if you are not sure the

cooktop is properly grounded.

It is not recommended to have a fuse in the neutral or ground

circuit.

Make sure that the electrical connection and wire size are

adequate and in conformance with the National Electrical Code,

ANSI/NFPA 70-latest edition or CSA Standards C22.1-94,

Canadian Electrical Code, Part 1 and C22.2 No. O-M91-latest

edition, and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

Before You Make the Electrical Connection:

To properly install your cooktop, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

A 4-wire or 3-wire, single phase, 240 volt, 60 Hz., AC only

electrical supply is required on a separate, 50-amp circuit

(36" [91.4 cm] models) or 40-amp circuit (30" [76.2 cm]

models), fused on both sides of the line.

The cooktop should be connected directly to the junction box

through flexible, armored or nonmetallic sheathed, copper

cable. The flexible, armored cable extending from the fuse box

or circuit breaker box should be connected directly to the

junction box.

Locate the junction box to allow as much slack as possible

between the junction box and the cooktop so that the cooktop

can be moved if servicing becomes necessary in the future.

Do not cut the conduit. The length of conduit provided is for

serviceability of the cooktop.

A UL listed or CSA approved conduit connector must be

provided at each end of the power supply cable (at the

cooktop and at the junction box). A listed conduit connector is

already provided at the cooktop.