KitchenAid KEC 설치 지침 매뉴얼 - 페이지 6

{카테고리_이름} KitchenAid KEC에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid KEC 10 페이지. Electric cooktop
KitchenAid KEC에 대해서도 마찬가지입니다: 설치 지침 매뉴얼 (16 페이지), 설치 지침 매뉴얼 (16 페이지)

페이지 인쇄

if codespermitanda separate ground

wireis used, i t is recommended thata

qualified electrician determine thatthe

groundpath

is adequate.

Do Not ground to a gas pipe.

Check with a qualified electrbian

if you

are not sure cooktop is properly

grounded.

Do Not have a fuse in the neutral or

grounding circuit.

The down@aft cooktop must be

connected to the proper electrical voltage

and frequency as specified on the

model/serial rating plate. The model/serial

rating plate is located on the bottom of the

cooktop.

[]

A four-wire or three-wire, singb-phase,

240-volt, 60-Hz, AC-only electrical

supply is required on a separate

30-ampere

circuit, fused on both sides

of the line.

[]

A time-delay

fuse or circuit breaker is

recommended.

The fuse size must not

exceed the circuit rating of the

appliance

as specified

on the

model/serial

rating plate.

[]

CONNECT

WITH COPPER WIRE

ONLY.

[]

Connected

directly

to the fused

disconnect

(or circuit breaker

box)

through flexible, armored

or non °

metallic sheathed,

copper cable (with

ground wire).

[]

Flexible armored cable should connect

cooktop directly to the junction

box.

[]

Fuse both sides of the fine.

[]

Locate the junction

box to allow as

much slack as possible

between the

junction

box and cooktop

so that the

downdraft

eooktop can be moved if

servicing

is ever necessary.

[]

A twist=on connector

and 1/2"

(12.7 mm) U.L o or CSA=listed conduit

connector

must be provided at the

junction

box.

The recommended

minimum

copper

wire size is No.-lO gauge.

However,

wire sizes and connections

must conform

to the requirements

of the National

Electrical

Code, ANSI/NFPA

70 -- latest

edition*, or CSA Standards

C22.1-94,

Canadian

Electrical

Code, Part 1 and

22.2

No. 0-M91 - latest edition** and all local

codes and ordinances.

Wire sizes and

connections

must conform with the rating

of the cooktop.

Copiesofthe standardlistedmay be obtained from:

* National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts02269

** CSA International

8501 East Pleasant Valley Road

CleveRand,Ohio 44131o5575

The wiring diagram is located on the

bottom of the cooktop.

Twist-on connector

and 1/2" (12.7 ram)

U.L o or CSA-listed

conduit connector

are

not provided.

Remove shipping materials and tape

from cooktop.

The blower is set to vent straight out

the back of the cooktop.

To vent to the left side, right side or down

through the bottom of the cabinet, add an

elbow to the blower assembly exhaust vent.

It may be easier to connect appliance

cable to junction

box before inserting

cooktop into cutout. See "Electrical

connections,"

Pages 6-8.

[] front edge of downdraft cooktop is at least

lq/2" (38.1 ram) from front edge of

countertop and parallel to countertop.

[] rear edge of cooktop is at least 3/4"

(19.1 ram) from rear wall as recommended.

[] side edge of cooktop is at least 6 inches

(152 cm) from side wall.

Connectvent system.See"Venting

requirements,"Pages4=5.Use duct tape to

sea! all joints.Vent must end with a wall or

roof cap outside the building.

This cooktop must be connected to a

grounded, metallb permanent wiring

system or a ground connector

shoumd be

connected to the ground terminam or wire

bad on the cooktop.

This cooktop is manufactured with a frame

connected, green or bare ground wire. Connect

the cooktop cable to the junction box through

the 1/2" (1£7 mm) U.L.=or CSA-listed conduit

connector. Complete electrical connection

according to local codes and ordinances.

Make the electrical connection:

Excessive

Weight Hazard

Use two or more peopte to move

and install cooktop.

Failure to do so can result in back

or other injury.

Lift entire

cooktop

up from cutout

when positioning

cooktop

countertop

opening.

insert downdraft cooktop into cutout.

Check that:

[] cooktop is centered in cutout.

Electrical

Shock Hazard

Turn power supply off before

connecting

wires.

Use !O-gauge solid copper wire.

Electrically

ground cooktop.

Failure to follow these

instructions

can result in death,

fire, or etectricaJ shock.