AFRISO 14 343 11 사용 설명서 - 페이지 2

{카테고리_이름} AFRISO 14 343 11에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. AFRISO 14 343 11 2 페이지.

페이지 인쇄

MOUNTING ON AN FIRST GENERATION ARV VALVE OR OTHER PRODUCER'S

VALVES

The ARM ProClick valve is factory set on 50% (position "5" on the scale). To mount the actuator pro-

perly on the valve, the valve must also be set on 50%.

1. Take off all the plastic parts from the valve, that will not be used.

2. Set the valve on 50%, so that the sleeve inside a 3-way valve will be right in the middle between

the hot and cold inlets

(Drawing

5) or just in the middle of the outlet connections in a 4-way valve

(Drawing

6).

3. Place the adapter on the stem of the valve and screw it down. Screw the two counter screws into the

valve

(Drawing

13). In first generation of AFRISO ARV valves (and most of other producer's valves),

the triangle on the adapter is in the same position as the flattening on the stem and indicates the

sleeve position inside the valve. To screw in the counter screws into first generation of AFRISO ARV

valves, sizes DN40 and DN50, one must unscrew the tightening Allen screws first

3-way

4-way

Drawing 13. Mounting the ARM ProClick actuator on an ARV valve

Full list of mounting sets for first generation of ARV valves

and other producer's valves is to be found in the technical

price catalogue on www.afriso.pl.

Drawing 14. ARV DN40-DN50 valve

3. Position of the knob with scale

After mounting the actuator on the mixing valve and correctly choosing the scale, position "0" should

mean a valve fully closed (hot water closed) and position "10" a fully open valve (hot water open).

Every other position will indicate a percentage of opening, e.g. position "4" means that the valve is

open in 40%.

4. Taking the actuator off the valve

To take off the actuator from the valve, press the pushbutton of the ProClick mechanism (1) and slide

the actuator from the valve (2).

Drawing 17. Dismounting the ARM ProClick actuator

TECHNICAL DATA

Parameter / piece

Value / description

Torque

6 Nm

Turning angle

Turning time by 90

ARM 323: 60 s

ARM 343: 120 s

Control signal / power supply

3-point / 230 V AC

Working temperature

0-50

Power consumption

2,5-4 VA

Safety class

Protection class

IP42

Dimensions (H x W x D)

85,5 x 97 x 99 mm

Housing

Cable length

2 m with plug

(Drawing

ProClick system disconnecting pushbutton

ARM ProClick actuator

f rst generation ARV valve

mounting set (Art. No. 14 101 10)

knob with a thicker part showing

4. Slide the actuator on the valve, so that the 2 counter pins fit inside the appropriate holes in the back

of the actuator and the mechanism locks itself on them. The construction of the actuator allows

to mount it in different positions

If it does not, one should pull off the knob and blue ring. Then mount it back with the indicator

pointing upwards.

5. Insert the double-sided scale in the correct position according to the opening/closing direction

("from 0 to 10" or "from 10 to 0)

If not, please return to point 2.

6. Connect the actuator to the controller according to the scheme

of the actuator can be detached. This makes mounting and electrical connections easier. To take

out the plug, one must lift the lever of the cover and slide it out

(Drawing

12). The plug fits into the socket only in one position.

USING THE ARM ProClick ACTUATOR

14).

1. Mode pushbutton

One must push the button to change from automatic to manual mode.

ring with indicator

double-sided scale

The mode pushbutton in the upper positon indicates automatic mode. When it is pushed down, one

can operate the actuator manually via the knob.

2. Signalling LEDs

The LEDs on the left and right inform about the turning direction of the actuator and valve. The left

one indicates turning counter-clockwise and the right clockwise. The shine also when the actuator is in

an end position but the controller still supplies power to the actuator. Observing the LEDs provides fast

diagnosis after finishing the assembly.

MAINTENANCE

The ARM ProClick actuator is a maintenance-free product.

DECLARATIONS AND STATEMENTS

Electric actuators ARM are produced according to the directives of the European Union regarding: low-

-voltage equipment LVD (2014/35/EU), electromagnetic compatibility EMC (2014/30/EU), restricting

the use of hazardous substances RoHS (2011/65/EU). Electric actuators ARM comply also with the follo-

wing standards: EN 60730-1, EN 60730-2-14.

DISMOUNTING, DISPOSAL

1. Disconnect the power supply.

2. Dismount the device.

3. To protect the environment, this product must not be disposed of together with regular household

waste. Dispose of the product according to local directives and guidelines.

This device consists of materials that can be reused by recycling companies.

WARRANTY

The manufacturer's warranty for this product is 36 months after the date of sale from

AFRISO sp. z o.o.. In case of any alteration in the product or usage against this instruction manual,

the warranty becomes void.

CUSTOMER SATISFACTION

For AFRISO sp. z o.o. customer satisfaction is the prime objective. Please contact us if you have any

questions, suggestions or problems concerning our product: [email protected], +48 32 330 33 55.

(Drawing

8). The blue ring with indicator must point upwards.

(Drawing

9). The blue indicator should point at "5" on the scale.

(Drawing

10). The electric cable

(Drawing

11). Next detach the plug

Drawing 15. Mode pushbutton

Drawing 16. LEDs