KitchenAid KECD865HBT0 설치 지침 매뉴얼 - 페이지 3
{카테고리_이름} KitchenAid KECD865HBT0에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid KECD865HBT0 8 페이지. 30" and 36" electric built-in ceramic downdraft cooktop
KitchenAid KECD865HBT0에 대해서도 마찬가지입니다: 부품 목록 (4 페이지)
페이지 인쇄
Product Dimensions
Cutout Dimensions
21-1.!
(54.4 cm)
depth
-15/16"
ram)
burner box
depth
Couetertopmust be
supported within
3" (7.6 cm) of cutout.
14-5/8"(37.1cm)
blowerhousing
depth
3-ft. (91.4 cm long
powersupply cable
factory installed.
Clearance Dimensions
30" (76.2 cm) man - 30" (76.2 cm) caoktop
36" (91.4 cm) nile - 36" (91.4 cm) cooktop
when higher thee 18" (45.7 cm) -4,_ I
/
I
See Note ** for
minimum clearaeces
to nearest combustible \\
Do Not seal
vertical surface
._
caoktapto caoetertap._..._
extendieg 18" (4&7 cm)
" _
..
above caoktap
_.
"-.
-
" .........................................
(25.4 rare)
_-_.
1"
29-1/2" (74.9 cm) - 36" (7&2 cm) cooktop
35-1/2" (9&2 crn) - 36" (61.4 cm) cooktop
cutout width
Side clearance -- 6" (15.2 cm) minimum clearance between side
of cooktop and side wall is recommended for maximum
ventilation performance.
Rear clearance -- 3/4" (19.1 ram) clearance between rear edge of
cooktop and rear wall is recommended.
Motor/blower
clearance -- 2" (51 ram) minimum clearance
between motor and cabinet is required for proper cooling.
6" (15.2 cm) clearance is recommended for servicing access.
_ Note: 24" (61 era) rainiraura when bottora of wood or rectal cabinet is
protected by not less than 1/4" (6.4 tara) flarae retardant raiJiboard covered
with not Jessthan No. 28 MSG sheet steel, 0.015" (0.4 rare} stainless stee_,
0,024" (0,6 rata) aJurainura or &020" (0,5 rata} copper,
30" (76,2 cra) rainiraura clearance between the top of the cooking p_atforra
and bottom of unprotected
wood or sheet metal
coaetertop
\
\
install rear
wall junction
box in shaded
area. Darker
shaded area is
preferred.
7
floor
11" (27.g cm)
6" (2&3 cm)
Minimum
base cabinet
dimensions
--
30" (76.2 cm) base cabinet width
24" (61 cm) base cabinet depth
25" (63.5 cm) countertop depth
Countertop
opening dimensions
that are shown must
be used. Given dimensions are minimum clearances and
provide required 0" (0 cm) clearance.
New installations
-- Follow minimum dimensions given:
Replacement installation
-- Be sure that front edge of
cooktop is at least 1=1/2" (38.1 mm) back from front
edge of countertop.
tf cabinet has drawers, drawers will need to be
removed and drawer fronts installed on front of cabinet.
Cutout preparation:
Decorative
laminate
--
Chamfer
all
exposed edges
to
prevent chipping
laminate,
Cut radius
corners
and file to
smooth
edges
and to
prevent
cracking.