IKEA DATID 설치 지침 및 사용 및 관리 매뉴얼 - 페이지 5

{카테고리_이름} IKEA DATID에 대한 설치 지침 및 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. IKEA DATID 18 페이지. 30" (76.2 cm) wall-mount canopy range hood
IKEA DATID에 대해서도 마찬가지입니다: 사용자 설명서 (16 페이지), 설치 매뉴얼 (12 페이지), 매뉴얼 (24 페이지)

페이지 인쇄

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools

listed here.

Tools needed

■ L evel

■ D rill with 1¼" (3.0 cm), ³⁄

■ P encil

■ W ire stripper or utility knife

■ T ape measure or ruler

■ P liers

■ C aulking gun and weatherproof caulking compound

■ V ent clamps

■ J igsaw or keyhole saw

■ F lat-blade screwdriver

■ M etal snips

■ P hillips screwdriver

■ M etric hex key set

Parts needed

■ H ome power supply cable

■ ½ " (12.7 mm) UL listed or CSA approved strain relief

■ 3 UL listed wire connectors

For vented installations, you will also need:

■ 1 wall or roof cap

■ M etal vent system

For non-vented (recirculating) installations, you will also need:

■ C harcoal Filter Kit Part Number W10412939 for non-vented

(recirculating) installations only. See "Assistance or Service"

section to order.

■ 6 " (15.2 cm) dia. round metal vent duct - length required is

determined by ceiling height.

Parts supplied

Remove parts from packages. Check that all parts are included.

■ H ood canopy assembly with ventilator and light bulbs installed

■ V ent transition with back draft dampers installed

■ M etal grease filter(s)

■ V ent cover support bracket

■ M ounting template

■ A ir deflector with extensions (for non-vented installations)

■ 2 -piece vent cover

■ 6 - 3.5 x 6.5 mm screws

■ 2 - 2.9 x 6.5 mm screws

■ 6 - 5 x 45 mm mounting screws

■ 6 - 8 x 40 mm wall anchors

■ T 10 Torx

adapter

®†

■ T 20

Torx

adapter

®†

†

TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

INSTALLATION REQUIREMENTS

" (9.5 mm), and ³⁄

" (4.8 mm) drill bits

■ 2 - Flat washers

■ 4 - 4.2 x 8 mm screws

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial

rating plate is located behind the filter on the rear wall of the

vent hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance.

Grounded electrical outlet is required. See "Electrical

Requirements" section.

The canopy hood is factory set for venting through the roof

or wall. For non-vented (recirculating) Installation see "For

Non-vented (recirculating) Installation Only" in "Connect Vent

System" section. Charcoal Filter Kit Part Number W10412939 is

available from your dealer or an authorized parts distributor.

All openings in ceiling and wall where canopy hood will be

installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title

24 CFR, Part 328 (formerly the Federal Standard for Mobile

Home Construction and Safety, Title 24, HUD, Part 280)

or when such standard is not applicable, the standard for

Manufactured Home Installation 1982 (Manufactured Home

Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or

latest edition, or with local codes.

Product Dimensions

10⁷⁄₈"

9³⁄₈"

(27.6 cm)

(23.8 cm)

30" (76.2 cm)

*For non-vented (recirculating) installations

**For vented installations

14"

(35.5 cm)

*32³⁄₈" (82.2 cm) min.

**31³⁄₈" (79.7 cm) min.

*44³⁄₄" (113.7 cm) max.

**41" (104.1 cm) max.

13³⁄₄"

(34.9 cm)

2" (5.1 cm)

18⁷⁄₈" (48.0 cm)