KitchenAid KFGS366VSS01 설치 지침 매뉴얼 - 페이지 6
{카테고리_이름} KitchenAid KFGS366VSS01에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid KFGS366VSS01 20 페이지. 30" (76.2 cm) and 36" (91.4 cm) gas built-in cooktop
KitchenAid KFGS366VSS01에 대해서도 마찬가지입니다: 부품 목록 (5 페이지)
페이지 인쇄
Style 2: Cooktop
over cabinets
1. Determine whether your cabinet construction
provides
clearance for installing clamping brackets at cooktop base
ends, This is the recommended
location. Clamping brackets
can be installed on the front and back of cooktop base
bottom, if necessary.
\
C
D
A. Attachment
screw holes for optional front and back
location.
B. Clamping bracket (end locations recommended)
C. cooktop base bottom
D. Attachment
screw
E. Attachment
screw location (recommended)
2. The clamping brackets can be installed before or after the
cooktop is placed into the cutout, Complete the following
steps for the option you choose.
Installing Brackets
Before Placing Cooktop
in Cutout
1. Using 2 or more people, place the cooktop upside down on a
covered surface.
2. Remove the attachment
screws for the selected bracket
locations from the bottom of the cooktop base.
3. Select bracket mounting holes that will allow the bracket to
extend far enough out from the cooktop for the installation of
21/2 '' (6.4 cm) clamping screws. See "Attach Cooktop to
Countertop"
for illustration of clamping screw installation.
i
I
I
A
7.
8=
Using 2 or more people, turn the cooktop right side up and
place in cutout,
NOTE: Make sure that the front edge of the cooktop is
parallel to the front edge of the countertop.
If repositioning
is
needed, lift entire cooktop up from cutout to avoid scratching
the countertop.
Loosen the screws and rotate the brackets so that they are
perpendicular
to the edge of the cooktop base and extend
beyond its edge, Securely tighten screws,
Installing Brackets After Placing Cooktop in Cutout
Using 2 or more people, place cooktop right side up into the
cutout.
NOTE: Make sure that the front edge of the cooktop is
parallel to the front edge of the countertop.
If repositioning
is
needed, lift entire cooktop up from cutout to avoid scratching
the countertop.
2. Remove the attachment
screws for the selected bracket
locations from the bottom of the cooktop base.
3. Select bracket mounting holes that will allow the bracket to
extend far enough out from the cooktop for the installation of
21/2 '' (6,4 cm) clamping screws.
4.
A. Cooktop
B. Cooktop base
C. Attachment
screw
D. Clamping bracket (extends far enough beyond cooktop
base to allow installation
of clamping screws)
E. 2_/2" (6.4 cm) clamping screw (to be installed in "Attach
Cooktop to Countertop")
F Countertop
Attach brackets to cooktop base bottom with bracket
attachment
screws using the bracket mounting holes
selected in Step 3. Securely tighten screws.
A. Edge of cooktop base bottom
B. Clamping bracket
4. Attach brackets to cooktop base bottom with bracket
attachment
screws using the bracket mounting holes
selected in Step 2,
5. Rotate brackets so they do not extend beyond edge of
cooktop base.
6. Tighten screws just enough to hold brackets in place when
cooktop is put in cutout.