Century Helicopter Products Bell 47G II ARF Helicopter 매뉴얼 - 페이지 4
{카테고리_이름} Century Helicopter Products Bell 47G II ARF Helicopter에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Century Helicopter Products Bell 47G II ARF Helicopter 15 페이지.
페이지 인쇄
This manual has been written for Century's 50 size Bell 47G II scale helicopter available in ARF
version and conversion kit. This is the detail construction of the Bell 47G II helicopter fuselage compo-
nents, landing gear, tailboom assembly which work in cooperation with the scale mechanics instruc-
tion manual. This manual should be reviewed before starting the assembly as there are steps in-
cluded that are different than in the generic scale mechanics manual. At steps that seem to be incor-
rect, simply refer back to this manual to find the correct components.
Instructional Detail
Instructional Detail
Instructional Detail
Instructional Detail
Instructional Detail
Every attempt has been made to ease the assembly of your helicopter, at each step where there are complex
assemblies, there are detailed drawings, photos and written instructions to walk you through each step.
Remember to take a few minutes before each step to carefully examine the instructions in order to become
familiar with the parts and assembly sequence before beginning that step.
Symbols used to help assist you in building the kit:
Full Scale
Drawing
Apply
oil
Special
Attention
Hardware Description and Identification:
M3x6 Phillips Machine Screw
M - metric
3 - diameter
6 - length
The tools and materials listed below are
the minimum needed to build the helicopter:
Screwdrivers - Slotted and Phillips head.
Long-Nosed Pliers, wide jaw pliers.
Allen Wrenches - 1.5mm, 2.0mm, 2.5mm.
( supplied in kit ) + 3.0mm
Appropriate Socket Wrench
(glow plug wrench for engine shaft nut)
Hobby Scissors, clear tape, masking tape
Double Sided Foam Tape ( 1/16" - 3/32" )
Foam Rubber ( radio packing )
JB Weld, Goop or Zap-a-Dap-a-Goo
Thread lock liquid (e.g. Locktite)
Hobby Grease ( Super Lube )
Oil to lubricate sliding shafts (Tri-Flow)
Drill bits 0.8mm[1/32"], 1.5mm[1/16"],
1.8mm[0.071"], 3mm[1/8"]
Bell 47G II Construction Manual
Repeat Steps
as specified
Apply
threadlock
Apply JB
Weld
M3x6 Self Tapping Screw
M - metric
3 - diameter
6 - length
Recommended Tools & Accessories
Recommended Tools & Accessories
Recommended Tools & Accessories
Recommended Tools & Accessories
Recommended Tools & Accessories
M3x6 = 3x6mm and can refer to screws or ball bearings.
M3x10 Socket Cap Screw
In addition, the following will make assembly and setup
easier, and prove useful later in your model toolbox:
CN2015
Hardened Tip Hex Screw Driver Set
CN2026
Pitch Gauge with Paddle Gauge.
CN2034
15
0
CN2052
Main Blade Balancer.
CN2054
Special Glow Plug Wrench Set.
CN2055
Ball Link Sizing Tool.
CN2070
Universal Flybar Lock.
CN2155
Piston Locking Tool.
CN2219
Ball Link Easy Driver.
CN2255
Control Rod Guage.
CNWI26555 5.5mm Nut Driver.
CNWI26570 7.0mm Nut Driver.
Partially
tighten
Purchased
Separately
Apply
Grease
3x7 Ball Bearing
M - metric
3 - diameter
10 - length
Curve Tip Ball link Pliers.
Helpful
Tip
Cut away
Shaded
Portion
M - metric
3 - inside
7 - outside
3