Green Leaf WORKHORSE SPRAYERS UTL Series 조립 및 작동 지침 매뉴얼 - 페이지 11

{카테고리_이름} Green Leaf WORKHORSE SPRAYERS UTL Series에 대한 조립 및 작동 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Green Leaf WORKHORSE SPRAYERS UTL Series 12 페이지.

페이지 인쇄

3300 Series: 2.2 GPM

PUMP INFORMATION:

Type - 3 chamber diaphragm pump, self priming,

capable of being run dry

Pressure Control - Demand

Liquid Temperature - 140°F (60°C) Max.

Priming Capabilities - 8 feet (2.4 m)

Max Pressure - 200 PSI (14 bar)

Inlet/Outlet Ports - 3/4" Quick Attach

Weight - 6 lbs (2.7 kg)

MOTOR INFORMATION

Leads - 14 AWG, 7˝ long with 2-Pin

Temperature Limits - Motor is not equipped

with thermal protection. For user safety, optimal

performance, and maximum motor life, the motor

surface temperature should not exceed 180°F (82°C)

Installation and Operation Precautions

y The pump is equipped with a pressure sensing demand switch that controls the maximum

operating pressure.

y In addition, never subject the pump to pressures above factory set/max pressure rating.

y As long as there is inlet water pressure, the pump will not stop forward flow of water even if the

motor is turned off. Be sure the system has positive means of shutting off water supply.

y Do not operate pump in an explosive environment. Arcing from the motor brushes, switch or

excessive heat from an improperly cycled motor may cause an explosion.

y Do not locate the pump motor near low temperature plastics or combustible material. The

surface temperature of the motor may exceed 180°F (82°C).

y Do not pump gasoline or other flammable liquids. Pump head materials are designed for use

with water only. Do not use with petroleum products.

y Do not assume fluid compatibility. If the fluid is improperly matched to the pumps' elastomers,

a leak may occur.

y To prevent electrical shock, disconnect power before initiating any work. In the case of pump

failure, the motor housing and/or pump fluid may carry high voltage to components normally

considered safe. Therefore, always consider electrical shock hazard when working with and

handling electrical equipment. If uncertain, consult an electrician. Electrical wiring should only

be done by a qualified electrician per local and state electrical codes.

Servicing —

y Every Year: Check system against operating standards. Flush with clean water and store in

warm dry place.

y Every 2-3 Years: We recommend replacing the valves and checking against operating

standards.

Remco Industries - 4605 County Rd 82 SE - Alexandria, MN - 763-253-4740 - www.remcoindustries.com

3200 Series: 3.2-4.0 GPM

PUMP INFORMATION:

Type - 3 chamber diaphragm pump, self priming,

capable of being run dry

Pressure Control - Demand

Liquid Temperature - 140°F (60°C) Max.

Priming Capabilities - 10 feet (3 m)

Max Pressure - 100 PSI (6.9 bar)

Inlet/Outlet Ports - 3/4" Quick Attach

Weight - 5 lbs (2.3 kg)

MOTOR INFORMATION

Leads - 14 AWG, 7˝ long with 2-Pin

Temperature Limits - Motor is not equipped

with thermal protection. For user safety, optimal

performance, and maximum motor life, the motor

surface temperature should not exceed 180°F (82°C)

Recommendations —

Electrical:

y The ProFlo™ series pumps are designed for intermittent duty. Make sure that "OFF" periods are

sufﬁcient. Consult the factory for particular data and design criteria.

y Be sure power supply used is adequate for the application.

y Pump and motor speciﬁctions are based on an alternator charged battery (13.6 VDC)

y Use sufﬁcient battery supply power. UTV and lawn tractor batteries may affect pump

performance due to low voltage and amp ratings

y Rapid On/Off Cycling must be limited to no more than 6 times per minute, even

if the pump is operating in the Continuous Duty zone. Cycling could cause the

motor to heat beyond the recommended maximum temperature, and reduce the

operational life of the pump and pressure-sensing switch.

Important return safety instructions -

When returning your pump for warranty or repair, you must always do the following:

y Contact factory for RMA number.

y Flush chemical residue from the pump (best done in the field).

y Tag pump with type of chemicals having been sprayed.

y Include complete description of operation problem, such as how pump was used, symptoms of

malfunction, etc. Since pumps can contain residues of toxic chemicals these steps are

necessary to protect all the people who handle return shipments, and to help pinpoint the

reason for the breakdown.

12 Volt DC Motor-Driven Diaphragm Pumps

5500 Series: 4.0-5.3GPM

PUMP INFORMATION:

Type - 5 chamber diaphragm pump, self priming,

capable of being run dry

Pressure Control - Demand

Liquid Temperature - 140°F (60°C) Max.

Priming Capabilities - 14 feet (4 m)

Max Pressure Capabilities - 150 PSI (10 bar)

Inlet/Outlet Ports - 3/4" Quick Attach

Weight - 8 lbs (3.62 kg)

MOTOR INFORMATION

Leads - 14 AWG, 7˝ long with 2-Pin

Temperature Limits - Motor is not equipped

with thermal protection. For user safety, optimal

performance, and maximum motor life, the motor

surface temperature should not exceed 180°F (82°C)