Frigidaire PLRU1778ES0 사용 및 관리 매뉴얼 - 페이지 4
{카테고리_이름} Frigidaire PLRU1778ES0에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Frigidaire PLRU1778ES0 10 페이지. Single-door refrigerator
Frigidaire PLRU1778ES0에 대해서도 마찬가지입니다: 정보 시트 (3 페이지), 사양 (1 페이지), 공장 부품 카탈로그 (9 페이지)
페이지 인쇄
LEVELING
The refrigerator must have all bottom corners resting firmly on a
solid floor. The floor must be strong enough to support a fully
loaded refrigerator . NOTE: It is Very Important for your
refrigerator to be level in order to function properly. If the
refrigerator is not leveled
during installation, the
door may be misaligned
and not close or seal
properly, causing
cooling, frost, or moisture
problems.
To Level Refrigerator:
After discarding crating
screws and wood base,
use a carpenter's level to
level the refrigerator from
front-to-back. Adjust the
plastic leveling feet in
front, ½ bubble higher, so
that the door closes
easily when left halfway
open.
Leveling Instructions for all Refrigerator/Freezer Pair:
•
Remove two leg levelers provided in literature bag. While
unit is lying on its back for wood skid removal, install both
leg levelers in rear of unit.
•
Level door of first unit using all four levelers and slide unit
into place. Recheck for levelness and adjust if necessary.
•
Measure distance from floor to bottom of door on first unit.
Adjust and level second unit so door height matches.
•
Leg Level Adjustments
•
One full turn of all four leg levelers will raise door 5/32".
•
One full turn of both front leg levelers will raise door
3/16" and tilt top of door back 7/16".
•
One full turn of both rear leg levelers will lower door
1/32" and tilt top of door forward 7/16".
•
One full turn of both side leg levelers will raise door
3/16" and tilt top of door 3/8".
•
Slide second unit into place leaving a minimum gap of 3/16"
between units for door swing clearance.
•
This last step may require at least one extraction of the
second unit to properly align units in a "built-in" application.
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
To allow door to close and seal properly, do not let food
packages extend past the front of the shelves
Unpacking and Leveling
Turn
Left To
Raise
Turn
Right To
Lower
Plastic
Leveling Feet
Discard The (4) Crating Screws
And (2) Wood Bases
Unpacking and Leveling
Shelf Front
DOOR REMOVAL
If door must be removed :
1.
Gently lay refrigerator on its back, on a rug or blanket.
2.
Remove two base screws and base panel.
3.
Remove bottom hinge screws.
4.
Remove plastic top hinge cover.
5.
Remove screws from top hinge.
6.
Remove top hinge from cabinet.
7.
Remove door and bottom hinge from cabinet.
8.
To replace door, reverse the above order and securely
tighten all screws to prevent hinge slippage.
Crating
Screw
TEMPERATURE CONTROLS
COOL DOWN PERIOD
For safe food storage, allow 4 hours for the refrigerator to
cool down completely. The refrigerator will run continuously
for the first several hours.
TEMPERATURE CONTROL
The temperature control is located inside the refrigerator
compartment. The temperature is factory
preset to provide satisfactory food storage
temperatures. However, the temperature
control is adjustable to provide a range of
temperatures for your personal satisfaction.
If a colder temperature is desired, turn the
temperature control knob toward COLDEST
and allow several hours for temperatures to
stabilize between adjustments.
4
FEATURES AT A GLANCE
Cold Control