CeoTronics CT-DECT Base 사용 설명서 - 페이지 10
{카테고리_이름} CeoTronics CT-DECT Base에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. CeoTronics CT-DECT Base 14 페이지. Headset for wireless duplex communication
CeoTronics CT-DECT Base에 대해서도 마찬가지입니다: 사용 설명서 (20 페이지), 사용 설명서 (20 페이지), 사용 설명서 (14 페이지), 사용 설명서 (20 페이지)
페이지 인쇄4.4.2 Connection setup and release by the base headset
(1)
Prerequisites
Ÿ Headsets subscribed (sections 3...3.2.2)
Ÿ Headsets switched on and synchronized (section 4.3)
(2)
Two-party conference
Connection setup: Briefly press the push-button » ) « on the left-hand side of the headset muff of
your base headset. When the connection is set up a high beep tone sounds in the calling base headset
and in the called standard headset. Subsequently duplex communication (speech and simultaneous
listening) is possible for both parties.
The microphone must be switched on in order to speak (see section 2.5). When the connection is active
a sidetone is audible in the headset while speaking. This is for the purpose of control.
Connection setup: Briefly press the push-button » ) « on the left-hand side of the headset muff of
your base headset. The base headset disconnects itself from the standard headset. A high beep tone
then sounds in the base headset and in the standard headset. The base headset and standard headset
are now on standby.
(3)
Three-party conference
Below the designations standard handset 1 and standard headset 2 are used only for the purpose of
better differentiation in the operating instructions. Both standard headsets operate with equal
entitlement.
Connection setup: Briefly press the push-button » ) « on the left-hand headset muff of your base
headset. The base headset sets up automatically a connection with the active standard headsets 1 and
2. Upon setup of the connection a high beep tone sounds in the calling base headset and in the called
standard headsets 1 and 2, and the base headset switches over automatically to three-party
conference mode.
The microphone must be switched on in order to speak (see section 2.5). When the connection is active
a sidetone is audible in the headset while speaking. This is for the purpose of control.
Connection release: Briefly press the push-button » ) « on the left-hand headset muff of your base
headset. The base headset disconnects itself from the standard headsets 1 and 2. This procedure is
acknowledged by a high beep tone in the base headset and in the standard headsets 1 and 2. The
three headsets are now on standby.
4.5
End of operation
Switch off the Headset with the ON/OFF switch and volume control knob (switch position OFF). This
guarantees a longer usage from the rechargeable battery. If necessary recharge the headset battery.
5.
Headset with level-limited ambient sound reception
5.1
General
The headset with level-limited ambient sound reception (ASR) (Fig. 3) is used mainly where ambient
sounds, warning signals etc, have to be heard perfectly alongside voice communication.
With ASR, ambient sounds can be received via a second microphone (Fig. 3/a) on the front side of the
right-hand headset muff and can be heard via one ASR speaker each in the right-hand and left-hand
headset muffs. The hearing of voice communication is also effected via one speaker each in the right-
hand and left-hand headset muffs. Even when receiving a message the external sound reception is in
operation.
10