IKEA IH5303WS0 설치 지침 및 사용 및 관리 매뉴얼 - 페이지 4
{카테고리_이름} IKEA IH5303WS0에 대한 설치 지침 및 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. IKEA IH5303WS0 28 페이지. 90 cm (35 2/5") wall-mount canopy range hood
페이지 인쇄INSTALLATION REQUIREMENTS
Gather the required tools and parts before starting installation.
Read and follow the instructions
provided with any tools listed
here.
Tools needed
•
Level
•
Drill with 11¼ '' (3 cm), 3/8"(9.5 mm), 7/64"(2.75 mm) and
1/8"(3 mm) drill bits
•
Pencil
•
Wire stripper or utility knife
•
Tape measure or ruler
•
Pliers
•
Caulking gun and weatherproof
caulking compound
•
Vent clamps
•
Jigsaw or keyhole saw
•
Flat-blade screwdriver
•
Metal snips
•
Phillips screwdriver
Parts needed
•
1/2"conduit
•
Two 1/2"(12.7 mm) UL listed or CSA approved strain reliefs
•
3 UL listed wire connectors
•
1 wall or roof cap
•
Metal vent system
•
Charcoal Filter Kit Part Number 4396848 for non-vented
(recirculating)
installations only. See "Assistance
or Service"
section to order.
Parts supplied
Remove parts from packages. Check that all parts are included.
•
Hood canopy assembly with ventilator and light bulbs
installed
•
Deflector for non-vented
(recirculating) installations
•
Plastic transition with back draft dampers installed
•
Literature package
•
Filter(s) - depending on model and size
•
2 mounting hooks
•
Vent cover support bracket
•
Mounting template
•
2-piece vent cover
•
4-4x8mmscrews
•
10- 3.5 x 9.5 mm screws
•
4-5x35mmscrews
•
2 - 2.9 x 9.5 mm screws
•
2-6x70mm
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility
to comply with installation clearances
specified on the model/serial rating plate. The model/serial
rating
plate is located behind the left filter on the rear wall of the vent
hood.
Canopy hood location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used. Given
dimensions
provide minimum clearance.
Grounded electrical outlet is required. See "Electrical
Requirements"
section.
The canopy hood is factory set for venting through the roof or
wall. For non-vented
(recirculating) Installation see "Non-vented
(recirculating) Installations"
in "Prepare Location" section.
Charcoal Filter Kit Part Number 4393848 is available from your
dealer or an authorized parts distributor.
All openings in ceiling and wall where canopy hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured
Home Construction
Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction
and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured
Home
Installation 1982 (Manufactured
Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local
codes.
Product Dimensions
33 1/16"
(84.0 cm)
16%"
(42.3 cm',
..... i :
................................................................
35 %" ...............................................................
(89.8 cm)
10 _3/_e"
(27.5 cm)
llllllllllll
21
1/4"
(%g.r.)
33 %e"
(84.0 cm)
aX.
3 1%6"
(10.0 cm)
2 3Is"
(6.0 cm)
J
%"
(2.3era)
315/16"
(10.0 cm)