Ganz ZC-Y41PH4 사용 설명서 - 페이지 2

{카테고리_이름} Ganz ZC-Y41PH4에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Ganz ZC-Y41PH4 2 페이지. Color ccd camera

페이지 인쇄

CONNECTION AND ADJUSTMENT

Important Note:

Qualified service personnel or system installers should perform the installation.

Make sure that the power is OFF before handling the power supply cable.

Power Supply Cable Connection

→ refer to PARTS DESCRIPTON (12)

Connect the power cable to the power input connector or terminal on the rear panel.

The camera automatically detects the power source (DC12V/AC24V).

Make sure the proper polarity for DC source.

Use RED terminal for +12VDC and BLACK for ground connection.

Improper polarity may cause damage to camera.

The Power LED on the rear panel is lit when the camera is connected to a power

source (refer to Parts Description 11).

Video Cable Connection

→ refer to PARTS DESCRIPTON (8)

Connect the 75Ω coaxial cable to video output terminal.

Auto Iris Lens Connections

→ refer to PARTS DESCRIPTON (4) & (7)

This camera supports manual iris lens, video auto iris lens,

and DC auto iris lens.

1. Video Auto Iris Lens Pin assignment

GND: Shield, ground.

+12V: Power source; +12VDC, 50 mA Max.

Video: Video signal output.

2. DC Auto Iris Lens

The 4 pin connection terminal is on the

rear panel. Refer to the pin assignment

to ensure the proper operation.

Lens Mounting

→ refer to PARTS DESCRIPTON (1)

1. Mount a lens onto the camera lens mount. Turn the lens clockwise.

2. This camera can accept CS-mount lens, or C-mount lens with a 5 mm adaptor ring.

Cautions for lens mounting:

1. In case of using a lens heaver than the camera, the lens and camera will require

additional support.

2. Do not over-tighten the lens onto the camera mount.

3. Do not rotate the lens counter-clockwise.

Focus Adjustment

→ refer to PARTS DESCRIPTON (2) & (3)

1. Loosen the back focus adjustment lever located

on the front head.

2. Adjust the screw to a desired position, and then

fix the screws.

Caution for focus adjustment:

1. Do not over-tighten the back focus screw.

2. Do not attempt to use any tools other than fingers to tighten the screw.

Improper focus adjustment may result in severe damages to the back-focus

echanism or to the CCD image sensor.

DIP SWITCHES SETTING

→ Refer to PARTS DESCRIPTION (6)

The row of DIP switches allow the following settings to be made:

•LL / INT

The line-lock mode enables the AC line phase adjustment.

Note: The line-lock sync mode is not available when the camera operates on DC

power.

•SDN / ON

This feature enables the camera operates in monochrome mode in reduced lighting.

Switch to ON to activate.

•BLC / ON

The Backlight Compensation feature eliminates the effect of strong background

lighting, maintaining the correct exposure. Switch to ON to activate. When switched

to BLC, the feature is off.

•AGC / TURBO

The Automatic Gain Control feature can improve picture quality in low lighting

conditions.

Select TURBO for most applications. Setting to AGC will reduce 'noise' from the

image,

but it will also limit the camera's sensitivity.

•AES/ ON

Selecting ON enables Electronic Iris mode, which compensates for excessive light

levels by automatically adjusting the camera shutter speed. This mode should only

be used with fixed or manual iris lenses.

•F.L. / ON

When this switch is set to ON, the camera reduces flicker in the image under

fluorescent lighting.

POTENTIOMETER SETTING

→ Refer to PARTS DESCRIPTION (9) & (10)

•LEVEL (Auto Lens Control Level Adjustment)

This potentiometer controls DC lenses:

it manages CCD sensor light quantity by adjusting lens IRIS aperture.

•V-Phase (Line Lock Phase Adjustment)

When the camera is set to Line-Lock mode (LL), it is possible to adjust camera

triggering point on the AC cycle in case of systems using sequential switchers

devoid of image digital process feature or video matrixes.