IKEA W10502581D 사용 및 관리 매뉴얼 - 페이지 5

{카테고리_이름} IKEA W10502581D에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. IKEA W10502581D 48 페이지. 30"(76.2cm) island-mount canopy range hood

페이지 인쇄

For non-vented (recirculating)

installations, you will also

need:

•

Charcoal Filter Kit Part Number W10412939 for non-vented

(recirculating)

installations only. See "Assistance

or Service"

section to order.

•

6" (15.2 cm) round metal vent duct. Length required is

determined by ceiling height.

Parts supplied

Remove parts from packages. Check that all parts are included.

•

Hood ventilator assembly with vent transition, back draft

damper, canopy glass, retainer brackets, rubber seals, and

light bulb installed.

•

Metal grease filter

•

66 - 4.2 x 8 mm screws (T20®t drive)

•

4 - 5 x 45 mm screws (#2 Phillips drive)

•

T10 Torx ®t adapter

•

T20 ®Torx®adapter

•

4-Vent

covers

•

4 - Plastic vent clips

•

Mounting template

•

Upper horizontal support bracket

•

Horizontal support

•

8- Vertical supports

•

2 - Vent cover supports

•

Air deflector (for non-vented/recirculating

installations)

IMPORTANT:

Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility

to comply with installation clearances

specified on the model/serial rating plate. The model/serial rating

plate is located behind the left filter on the rear wall of the vent

hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions

provide minimum clearance.

Grounded electrical outlet is required. See "Electrical

Requirements"

section.

Because of the size and weight of this island hood, the chimney

support must be securely attached to the ceiling.

•

For plaster or drywall ceilings, the chimney support must be

attached to joists. If this is not possible, you must build a

support structure behind the plaster or drywall. The support

structure must be able to support 80 Ibs (36.6 kg).

The range hood is factory set for venting through the roof or wall.

For non-vented (recirculating) Installation see "Non-vented

(recirculating) Installation"

in "Install Range Hood" section.

Charcoal Filter Kit Part Number W10412939

is available from

your dealer or an authorized parts distributor.

All openings in ceiling and wall where range hood will be installed

must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured

Home Construction

Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction

and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured

Home

Installation 1982 (Manufactured

Home Sites, Communities

and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

1-®TORX and T20 are registered

trademarks

of Saturn Fasteners, Inc.

Product Dimensions

A. 12_" (31.1 cm)

B. 13_/'

(33.5

cm)

C. "29_" (75.6 cm) min. 44 _" (113.8 cm) max.

*'29_" (75.6cm) min. 491_,, (126.5 cm) max.

D. 3 ½" (8.9 cm)

E. 30" (76.2 cm)

F. 25 _/' (64.0 cm)

*Vented installations only

**Non-vented

(recirculating)

installations only

Installation Dimensions

A. Countertop

height

B. Hood height from ceiling to bottom of the range

hood filter surface: D-A-C=B

C. Hood height: 24" (61.0 cm) min. from electric

cooking surface, 27" (68.6 cm) min. from gas

cooking surface, suggested 36" (91.4 cm) max.

D. Ceiling height

IMPORTANT:

Minimum distance "C": 24" (61.0 cm) from electric cooking

surface, 27" (68.6 cm) from gas cooking surface

Suggested maximum distance "C": 36" (91.4 cm)