KitchenAid 97415 14 설치 지침 매뉴얼 - 페이지 3

{카테고리_이름} KitchenAid 97415 14에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid 97415 14 7 페이지. Undercounter

페이지 인쇄

Product Damage

Heavy duty door springs must be

used with custom panels that weigh

more than 4 pounds.

Heavy duty

door springs are attached

to the

right mounting

bracket located

behind the toe panel or can be

ordered from your dealer or

authorized

parts distributor.

Order

Door Spring Kit, Part Number

9741247.

Maximum

door panel weight

is 10

pounds.

Failure to follow

these instructions

could cause product

damage.

Dishwasher door panel and access panel

can be customized to match wood

cabinets. It is recommended

that a cabinet-

maker cut the customized

panel pieces

because of the precise dimensions needed.

Cut wood panels so that wood grain

matches direction of grain in cabinets.

File or sand edges of wood panels.

Apply moisture-resistant

sealer on all

sides of wood panels.

S/16" routed

four sides for panel

more than l/4" thick

Model

E;;;;:;;'

23-9116"

17-7116"

23-l l/16"

6-518"

23-9116"

18-13/16"

23-11116"

6-5/W

Dimensions

for routing

panel edges

Custom panels

l/4" max.

more than l/4"

thick: Route outer

edge.

Custom panels

less than l/4"

5/16" min.

thick: lnstajl

spacer behind

panel.

Side View

Panel B

panel

Electrical Requirements

Electrical Shock Hazard

Electrical ground

is required

on this

appliance.

If cold water pipe is interrupted

plastic, non-metallic

gaskets or

other insulating

materials,

Do Not

use for grounding.

Do Not ground

to a gas supply

pipe.

Do Not have a fuse in the neutral or

grounding

circuit. A fuse in the

neutral or grounding

circuit could

result in an electrical

shock.

Do Not modify the power supply

cord plug.

Do Not use an extension

cord with

this appliance.

Check with a qualified

electrician

you are in doubt as to whether

this

appliance

is properly

grounded.

It is the customer's

responsibility

to:

Contact a qualified

electrical

installer.

Assure that the electrical

supply is

adequate

and in conformance

with

the National

Electrical Code,

ANWNFPA

70 - latest edition*,

and all local codes and ordinances.

Failure to follow

these instructions

could result in serious injury or death.

If codes permit and a separate ground-

ing wire is used, it is recommended

that

a qualified

electrician

determine

that the

grounding

path is adequate.

A single-phase,

11 j-volt,

60-Hz, AC-only,

15 or 20-ampere, fused electrical supply is

required. Time-delay fuse or circuit breaker

is recommended.

It is recommended

that a

separate circuit, serving only this appliance,

be provided.

This appliance may be connected with

flexible armored or non-metallic

sheathed

copper cable (with grounding

wire). A

conduit connector must be installed at the

junction

box. Wire sizes (COPPER WIRE

ONLY) must conform with the rating of the

dishwasher.

-------

A.'

! '.

Electrical connection

Direct wire connection

.q *

? %. Cut a 1" hole in the cabinet for the

electrical wiring to pass through.

If this hole

is cut in a wood cabinet, the hole should be

sanded until smooth. If the hole is cut in a

metal cabinet, the hole must be covered by

a grommet (Part No. 302797). Run flexible

cable from fused disconnect, circuit breaker

or junction

box through

hole in cabinet.

Cable should extend 24 inches minimum

from back wall and easily connect to

terminal box.

8 Disconnect

power supply.

After dishwasher

is installed

ing, remove terminal box cover.

Install conduit connector to box.

Insert power cable through

conduit

Using twist-on connectors, connect

power supply cable to white

leads in terminal box. Connect black wire

of power supply cable with black wire in

terminal box.

gr Connect grounding

wire of power

supply cable to grounding

screw on

dishwasher frame.

*Tighten

conduit connector screws.

Replace terminal box cover.

Flexible power supply cord

connection

3-prong

grounding-type

wall receptacle

3-prong

grounding

Local codes may permit the use of a U.L.-

listed, flexible, three-conductor,

16-

gauge, power supply cord terminated

with a three-prong,

grounding-type

plug.

It is recommended

that cord kit, Part No.

675456, available from your KitchenAid

dealer or parts supplier, be installed.

Follow Installation

Instructions

packaged

with flexible power supply cord.

The flexible

power supply cord used

must:

Be less than 6 feet in length.

Meet National Electrical Code,

ANSVNFPA 70 -

latest edition*,

and all

local codes and ordinances.

Not touch the dishwasher motor or

lower portion of the dishwasher tub.

A grommet,

Part No. 302797, must cover

the hole cut in a metal cabinet for the

flexible power supply cord.

To minimize possible shock hazard, the

cord must be plugged into a mating three-

prong, grounding-type

wall receptacle

grounded

in accordance with National

Electrical Code 70 -

latest edition* and all

local ordinances.

If a mating wall receptacle is not available, it

is the personal responsibility

and obligation

of the customer to have a properly

grounded

3-prong wall receptacle installed

by a qualified electrician.

The receptacle should be installed on the

rear or side wall of the cabinet next to the

dishwasher opening.

* Copies of the standard

listed may be

obtained

from:

National Fire Protection Association

Batterymarch

Park

Quincy, Massachusetts 02269