Ganz PixelMaster PRO NR8H 빠른 매뉴얼 - 페이지 3

{카테고리_이름} Ganz PixelMaster PRO NR8H에 대한 빠른 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Ganz PixelMaster PRO NR8H 4 페이지.

Ganz PixelMaster PRO NR8H 빠른 매뉴얼
Automatic Recording Setting
Recording
Press [MENU] on remote control, and use the
1.
direction buttons to select <RECORD SETUP>
and press [ENTER]
Alternatively, you can select <MENU> - <RECORD
SETUP> from the status bar.
Set <RECORD SETUP MODE> to <AUTO
2.
CONFIGURATION>.
Select "Automatic Record Configuration Mode".
3.

Time Search

Search
From the <SEARCH> menu, select <TIME
1.
SEARCH>
Specify the search date and time from the calendar
2.
in the left corner of the screen.
You can identify the type of the recording data by
3.
the color in the bar.
Network Connection Setting
Network
Setting
Connect the [WAN(UPLINK)] port in the rear panel
1.
of the NVR to any port available except for the WAN
port of the router.
Connect the [WAN(UPLINK] port of the router directly to
2.
the fixed IP LAN cable, or connect it to the xDSL modem.
Check the network address information if using a
3.
network environment connected to the same router.
Enter the network setting menu of the NVR and
4.
provide the IP address.
Enter an IP address that falls in the privete IP range provided
by the router.
Ex) 192.168.1.2-254, 192.168.0.2-254, 192.168.xxx.2-254
3) When done, configure the port forwarding for RTSP
and Web Service ports by clicking Port Forwarding.
(The default value of the Web service port is 8080.)
4) Click <PORT FORWARDING> for each. You will see
the confirmation message. Click <APPLY> and edit
the menu.
5) The network settings of the NVR are complete.
Some router models may not support UPNP properly.
If you see a failure message after <PORT FORWARDING>
settings, refer to the user manual of the router and configure
the DMZ or port forwarding settings manually.
>ALWAYS HIGH VIDEO QUALITY : Recording will
proceed in the best quality regardless of the event
at all times.
As this option will always make recording in the
best quality, the recording period is the shortest
compared to the other recording mode.
>MOTION RECORD : Recording will proceed only
If a motion is detected.
>Pink (PRE RECORDING) : The pre-recording is
performed on the recording data after you set the
<PRE RECORDING TIME> from <OPERATION
MODE>.
>Green (Continuous) : The continuous recording is
performed on the recording data.
To configure the network settings
1) From the main menu of the NVR, move to <SYSTEM
SETUP> - <NETWORK> - <IP SETUP>.
2) Uncheck the DHCP checkbox and provide the
necessary information manually.
(Check the network address information in the
network environment settings and enter the correct
information.)
When the network configuration is complete,
5.
proceed with the DDNS settings to allow access to
the NVR from outside.
From the main menu of the NVR, move to <SYSTEM
SETUP> - <NETWORK> - <DDNS>.
Rename the NVR, (The default name of the NVR is the
6.
MAC address of the NVR.)
Enter a desired name in combination or characters and
numbers.
>ALARM RECORD : Recording will proceed only
if alarm event occurs.
>MOTION/ALARM RECORD : Recording will
proceed only if a motion is detected or an alarm
event occurs.
>INTENSIVE MOTION RECORD : Normally
recording will be performed in a low quality.
However, the quality will switch to high if a motion
is detected.
>INTENSIVE ALARM RECORD : Normally
recording will be performed in a low quality.
However, the quality will switch to high if an alarm
event occurs.
>INTENSIVE MOTION/ALARM RECORD : Normally
recording will be performed in a low quality.
However, the quality will switch to high if a motion
is detected or an alarm event occurs.
Click <APPLY>.
4.
>Red (Alarm) : The alarm event recording is
performed on the recording data.
>Blue (Motion) : The motion event recording is
performed on the recording data.
>Yellow (Panic) : The panic manual recording is
performed on the recording data
Click to move to desired start time in the time bar,
4.
or use the buttons at the bottom of the status bar to
make search.
Select an item to play and click <PLAY>.
5.
Click to move to desired time, or simply double-click a
desired time in the time bar to play the video data on the
time.
For details on the thumbnail search and event search, refer
to the user manual.
>IP ADDRESS : 192.168.1.116 (enter the network IP
address.)
>GATEWAY:192.168.1.1 (enter the gateway address)
>SUBNET MASK:255.255.255.0 (type the subnet
mask.)
>The primary, the secondary DNS server:
168.126.63.1 (enter the address of a DNS server.)
When done, click <DDNS REGISTRATION TEST>
7.
and <DDNS CONNECTION TEST> in this order.
If you receive a success message, check the NVR
address and click <APPLY> at the bottom.
Check the NVR address and the Web service port in
8.
the network settings to make sure that any Internet-
connected PC can access the NVR.
If you type "mydvr" for the NVR name from DDN
9.
item, the address of the Web viewer is
"http://mydvr.dvrlink.net:8080/