KitchenAid KDTE104ESS3 기술 시트 - 페이지 3

{카테고리_이름} KitchenAid KDTE104ESS3에 대한 기술 시트을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid KDTE104ESS3 12 페이지.

페이지 인쇄

INTERVAL

CYCLE, OPTION, AND STATUS LEDs

1 HR WASH

NORMAL

START/RESUME

RUNNING (Front Status light)

HI TEMP

DRY OPTION

SANITIZED

CLEAN/ 7-Seg

ALL OTHER CYCLE, OPTION, AND STATUS LEDs

INTERVAL TIME (min:sec)

TOTAL TIME (MAX.): 22:57

SOIL SENSING INTERVALS

AND SENSOR CHECKS

THERMISTOR (TEMPERATURE SENSOR)

CHECK INTERVAL

OWI (SOIL SENSOR) CHECK INTERVALS NOTE 6

NOTE: OWI has thermistor built in - see check above

DIVERTER POSITION SENSOR CHECK NOTE 3

SALT LEVEL REED SWITCH/

FLOWMETER INPUT TEST

LOADS

PILOT RELAY

VENT

FILL

WASH MOTOR

DISPENSER (DETERGENT/RINSE AID)

DIVERTER

DIVERTER POSITION

DRAIN MOTOR

HEATER

DC FAN MOTOR (IF PRESENT)

AC FAN MOTOR (IF PRESENT)

REGEN (IF PRESENT)

Service Diagnostics Cycle Notes:

To invoke the Diagnostics cycle, perform the following while

in standby:

Press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no

■

more than 1 second between key presses.

The Service Diagnostics Cycle will start when the door is closed.

■

To rapid advance 1 interval at a time, press the Start/Resume key.

■

Rapid advance may skip sensor checks as some checks require

2 complete intervals.

NOTE: While you are in the Diagnostic Cycle, the Start/Resume

feature is turned Off (for example, Auto Resume after door interrupts)

and the Start/Resume key becomes an interval advance key.

Invoking Service Diagnostics Cycle clears all status and last run

■

information from memory and restores defaults. It also forces the

next cycle to be a Sensor Calibration cycle.

Drain and wash motors will pulsate on and off.

■

Last run cycles and options returned to default.

■

Last run delay returns to the lowest delay increment.

■

Calibration cycle may force an extra rinse to occur prior to Final

■

Rinse (to assure clear water), then calibrates the O.W.I. and the fill

amount during the final rinse.

Operating state returns to Standby upon completing or

■

terminating the Service Diagnostics Cycle.

Reference the "Service Diagnostics with Error Codes" section

■

for details.

To quickly advance through customer cycles, invoke the Rapid Advance

mode by pressing HIGH TEMP - HEATED DRY - HIGH TEMP - HEATED DRY,

after starting the cycle. Then, press START/RESUME to advance through

cycle intervals.

Service Diagnostics Cycle

26 25 24 23 22 21

1HR

NRM

STA STA STA STA STA STA

RUN RUN RUN RUN RUN RUN

HIT

DRY

NOTE 5

SAN

NOTES

4,5,6

CLN

7-Seg

7-Seg 7-Seg 7-Seg

ALL

NOTE 5

NOTE 8

NOTE 7

Customer Cycle Operation

18 17 16 15 14 13 12

1HR

NRM

STA

STA STA STA

RUN

RUN RUN RUN RUN RUN RUN RUN

HIT

DRY

(SAN)

(CLN)

THR

OWI

DIV

PLT

PLT PLT

PLT

PLT PLT

VNT

VNT VNT VNT VNT

FIL

WSH WSH

DSP

DIV

(DIV)

UPR UPR UPR UPR

UPR

FAN

Turn on all LEDs immediately upon receiving the entry sequence (even

if the door is open) for 5 seconds as a display test. Turn off all LEDs for

1 second prior to reporting customer error history.

Diverter will be on continuously in interval 14. In all other diverter

intervals, diverter will be on only until it reaches the intended position

for that interval.

Press HI TEMP key in this interval to clear customer error history.

Thermistor (temperature sensor) checks - turn clean LED on if

thermistor is in its normal temperature range 32°F to 167°F (0°C to

75°C). Turn sanitized LED on if fill temperature is above 65°F (18.3°C).

OWI (optical soil sensor) checks:

Check OWI sensor for the presence of water during the 5-sec.

■

pause in interval 16 and turn on the Clean LED in interval 15 if

water detected.

Check OWI sensor for presence of bulk soil during pause interval

■

13 and turn on the Clean LED in interval 12 if bulk soil detected.

DC fan motor is On during upper rack washing intervals.

Turn on Sanitized LED in this interval to indicate that the salt level reed

switch is closed.

Turn on Clean LED in this interval to indicate that vent current

is detected.

NOTE: Rapid Advance mode is automatically enabled in the Service

Diagnostics cycle but must be manually invoked in customer cycles.

11 10 9

1HR

NRM

STA

STA STA STA STA

STA STA STA

RUN RUN RUN RUN RUN RUN RUN RUN

HIT

DRY

(CLN)

OWI

PLT

PLT PLT PLT

PLT

PLT PLT

VNT VNT VNT VNT VNT VNT

VNT VNT

WSH WSH WSH

(DIV) (DIV)

(DIV)

UPR

LOW LOW LOW LOW LOW LOW

UPR

DRN

HTR

6 5

1HR

NRM

STA

RUN

RUN RUN

HIT

DRY

(SAN)

7-Seg 7-Seg

SRM

PLT

VNT

LOW

DRN

HTR

FAN

REG