KitchenAid KIDS36EPSS 설치 지침 매뉴얼 - 페이지 6
{카테고리_이름} KitchenAid KIDS36EPSS에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid KIDS36EPSS 6 페이지. In-sink dishwasher
페이지 인쇄WARNING
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green
ground connector in terminal
box.
Do not use an extension cord.
Failure to do so can result in
death, fire, or electrical shock.
ground
wire
direct
green ground
wire
7F .
Pull direct wire through
conduit connector and connect wires
as follows:
• Form ground wire into a hook and
wrap clockwise around ground
screw under washer. Tighten
ground screw securely.
• Use twist-on connectors of proper
size to connect direct wire to
16-gauge wire dishwasher wiring.
Connect black wires together and
white wires together.
• Tighten conduit connector screws.
terminal
box
tabs
7G.
Reinstall terminal box.
Important: The tabs MUST be under
the terminal box as shown.
Part No. 8529408
® Registered Trademark/™ Trademark of KitchenAid, U.S.A.
® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.
© 2002 All rights reserved.
®
apply Teflon
or pipe joint
compound
DO NOT apply Teflon
tape or pipe joint
compound
8.
Apply Teflon
compound to 90° elbow fitting and
connect fitting to water inlet valve.
Use adjustable wrench and tighten
elbow until snug and facing the
direction needed for your water fill
line installation.
IMPORTANT: If you are installing the
Hot Water Accessory Tank, go back
to its Installation Instructions and
complete the installation at this time.
9.
Connect the dishwasher water
screw
fill line.
• Slide nut onto copper tubing about
1 inch.
• Slide ferrule onto the tubing. Do
not position ferrule on end of
tubing.
• Put tubing into fill fitting as far as it
will go.
• Slide nut and ferrule forward and
start nut onto elbow threads. Be
careful when handling and
positioning copper tubing. It bends
and kinks easily.
• With copper tubing pushed into
elbow as far as it will go, use a 5/8"
open-end wrench and tighten the
compression nut securely.
10.
Connect hot and cold water
lines to faucet.
11.
Connect the sink and
dishwasher drain plumbing.
12.
Turn water supply on to
both dishwasher and sink faucet.
Check for leaks.
tape
water inlet
valve
water fill line
connection
®
®
tape or pipe joint
13.
Check that there is power to
the outlet and plug power supply
cord into 3-prong grounded outlet. If
direct wired, turn on power supply.
Important: The following steps
MUST be done BEFORE using the
dishwasher, to test and activate the
GFCI.
test
reset
indicator
14.
Press the reset button on
the GFCI. The indicator should be
visible.
15.
Press the test button on the
GFCI. The indicator should
disappear.
16.
Press the reset button. The
indicator should reappear.
If the GFCI fails this test, DO NOT use
dishwasher. Call the KitchenAid
Customer Interaction Center toll-free
at 1-800-422-1230 for assistance.
17.
Refer to Use and Care Guide
that came with this dishwasher and
run dishwasher through a complete
cycle.
If Hot Water Accessory Tank is
installed, wait about 45 minutes
before starting the next dishwasher
cycle to allow the hot water tank to
finish heating. (Refer to the
Installation Instructions and Use and
Care Guide supplied with Hot Water
Accessory Tank.)
When the hot water tank is first
heated, it is normal for a small
amount of water to be discharged
into the dishwasher.
Check for leaks.
Printed in U.S.A.
8/2002