KitchenAid KUDC02IR 소비자 참조 매뉴얼 - 페이지 8

{카테고리_이름} KitchenAid KUDC02IR에 대한 소비자 참조 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. KitchenAid KUDC02IR 16 페이지. Kitchenaid undercounter dishwasher dimensions
KitchenAid KUDC02IR에 대해서도 마찬가지입니다: 치수 (1 페이지), 치수 (1 페이지)

페이지 인쇄

You can customize your cycles by pressing the options desired. If

you change your mind, press the option again to turn off the

option. Select a different option if desired.

You can change an option anytime before the selected option

begins. For example, you can press HEAT DRY anytime before

drying begins.

Press START/RESUME to repeat the same cycle and options as in

the previous wash cycle.

NOTE: If the last cycle you completed was a rinse cycle, when

you press Start/Resume, the dishwasher runs the last full wash

cycle and options.

Hi-Temp Scrub

Select this option to heat the water during parts of the cycle, and

add a rinse. Higher water temperatures and an extra rinse help

clean tough soils. Hi-Temp Scrub, with the Heavy Duty cycle,

heats the water in the main wash and the prewash. Hi-Temp

Scrub, with the Normal cycle, raises the water temperature in the

main wash.

This option adds heat, water, and wash time to a cycle.

NOTE: Hi-Temp Scrub is an option with the Heavy Duty and

Normal cycles.

SANI RINSE™ Option (on some models)

Select this option to raise the water temperature in the final rinse

to approximately 155°F (68°C). The SANI RINSE™ option adds

heat and time to the cycle. This high temperature rinse sanitizes

your dishes and glassware in accordance with NSF/ANSI

Standard 184 for Residential Dishwashers. Certified residential

dishwashers are not intended for licensed food establishments.

NOTE: The Heavy Duty cycle automatically uses this option. SANI

RINSE™ is an option with the Normal cycle. Only these

sanitization cycles have been designed to meet the NSF/ANSI

requirements.

Heat Dry

The Heat Dry option in combination with rinse aid will give you

excellent drying results. The energy to use Heat Dry costs pennies

per cycle. Heat Dry is on when the light is lit on the Heat Dry

button. Be sure to load plastic items in the upper rack to avoid

damage.

You may turn off the Heat Dry option by pressing HEAT DRY so

that the light goes off. However, you will have items in your dish

load that will not be dry at the end of the cycle.

NOTE: The Heat Dry option is used in all cycles except Rinse

Only.

Clean

Clean light glows when a cycle is finished. The light turns off when

you open and close the door or press CANCEL.

Option Selections

Control Lock

Use Control Lock to prevent unintended use of your dishwasher.

You can also use the control lock feature to prevent unintended

cycle or option changes during a cycle.

When Control Lock is lit, all buttons are disabled.

NOTES:

The dishwasher door can be opened while the controls are

locked.

You can turn on the lock while the dishwasher is running.

To turn on the lock

Press and hold HEAT DRY for 5 seconds. The Control Lock light

glows.

If you press any pad while your dishwasher is locked, the light

flashes 3 times.

To turn off the lock

Press and hold HEAT DRY for 5 seconds. The Control Lock light

turns off.

4 Hour Delay (on some models)

Select this option to run your dishwasher at a later time or during

off-peak hours. You can add items to the load anytime during the

delay countdown. (See "Adding Items During a Cycle.") The delay

countdown will not continue if the door is not latched.

To delay the start (Models KUDI02IR, KUDL02IR,

KUDI02CR, KUDK02CR, KUDJ02CR)

1. Close the door.

2. Select a wash cycle and options. The selected cycle and

option lights will glow.

3. Press 4 HOUR DELAY. The 4 Hour Delay light will glow.

4. Press START/RESUME.

NOTE: To cancel the delay, press 4 HOUR DELAY. Press START/

RESUME to immediately start your dishwasher.

To delay the start (Models KUDI02FR, KUDL02FR)

1. Open the door.

2. Select a wash cycle and options. The selected cycle and

option lights will glow.

3. Press 4 HOUR DELAY. The 4 Hour Delay light will glow.

4. Press START/RESUME.

5. Close the door firmly within 3 seconds of pressing Start/

Resume.

NOTE: To cancel the delay, open the door and press 4 HOUR

DELAY. Press START/RESUME and close the door firmly to

immediately start your dishwasher.

Status Indicators

Sanitized (on some models)

If you select the SANI RINSE™ option, Sanitized light glows when

the SANI RINSE™ cycle is finished. If your dishwasher did not

properly sanitize your dishes, the light flashes at the end of the

cycle. This can happen if the cycle is interrupted. The light goes

off when you open and close the door or press CANCEL.