IKEA IUD6000R 사용 및 관리 매뉴얼 - 페이지 10

{카테고리_이름} IKEA IUD6000R에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. IKEA IUD6000R 36 페이지.

페이지 인쇄

Rinse a ids keep water f rom forming d roplets thatcandryas

spots orstreaks. They alsoimprove drying byallowing water t o

drain offofthedishes d uring t hefinal r inse byreleasing asmall

amount oftherinse aidintotherinse water. Your d ishwasher is

designed tousealiquid rinse aid. D onotuse a solid orbar-type

rinse aid.

Checking the dispenser

Check the center of the fill indicatorcap. Clear means it needs

filling.

Or you can remove the fill indicator cap. If an "E" is visible, the

dispenser is empty.

Filling the dispenser

The rinse aid dispenser holds 6 oz (175 mL) of rinse aid. Under

normal conditions,

this will last for about 3 months. You do not

have to wait until the dispenser is empty to refill it. Try to keep it

full, but be sure not to overfill it.

1. Make sure the dishwasher

door is completely open.

2. Remove the fill indicator cap.

3. Add rinse aid. Fill to the smallest opening in the lower part of

the dispenser. Overfilling can cause the rinse aid to leak out,

and could cause oversudsing.

4. Clean up any spilled rinse aid with a damp cloth.

5. Replace the fill indicator cap. Close tightly.

Hot water dissolves and activates the dishwashing detergent.

Hot water also dissolves grease on dishes and helps glasses dry

spot-free. For best dishwashing

results, water should be 120°F

(49°C) as it enters the dishwasher. Loads may not wash as well if

the water temperature is too low. Water that is too hot can make

some soils harder to remove and cause certain detergent

ingredients not to function. If your water heater is located far from

the dishwasher, it may be necessary to run the hot water at the

faucet closest to the dishwasher to minimize the amount of cold

water in the water line.

To check water temperature

1. Run hot water at the faucet closest to your dishwasher for at

least 1 minute.

2. Place a candy or meat thermometer

in a glass measuring

cup.

Check the temperature

on the thermometer

as the water is

running into the cup.

Additional efficiency tips

Use a delay feature (on some models) to run your dishwasher

during oft-peak hours. Local utilities recommend

avoiding

heavy usage of energy at certain times of day.

During the summer, run your dishwasher at night. This

reduces daytime heat buildup in the kitchen.

Use the energy-saving dry option whenever possible. Allow

longer drying times (overnight) when using these options. Use

a rinse aid to improve drying.

Use cycles or options that add extra heat to the wash or rinse

portion of the cycle only when needed.

Run your dishwasher with full loads. Run a rinse cycle after

meals until the dishwasher is full.

If your home is equipped with a water softener, you may want

to avoid starting the dishwasher during the regeneration of

the softener, since this may contribute to poor wash

performance.

For Series 4000:

Turn thecyclecontrol knob to thedesired cycle. Ifthedoor is

latched, y ou will hearthecyclesstart and stop as the cycle

control knob passes each cyclemark. Thisisnormal and does

nothurtthe dishwasher. If you prefer, you can setthecycle

control knob withthedoor unlatched.

For Series 6000:

Press the desired cycle. Turn the cycle control knob to the

desired cycle. If the door is latched, you will hear the cycles start

and stop as the cycle control knob passes each cycle mark. This

is normal and does not hurt the dishwasher. If you prefer, you can

set the cycle control knob with the door unlatched.

To use Rinse Only, press HEAVY or NORMAL and turn the cycle

control knob to Rinse Only.