Makita 1806B 사용 설명서 - 페이지 5
{카테고리_이름} Makita 1806B에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Makita 1806B 10 페이지. Power planer
Makita 1806B에 대해서도 마찬가지입니다: 사용 설명서 (17 페이지), 부품 분석 (3 페이지), 사용 설명서 (13 페이지), 사용 설명서 (13 페이지), 사용 설명서 (11 페이지)
페이지 인쇄
ENGLISH
1 Hex wrench
2 Bolt
3 Adjusting screw
4 Planer blade
5 Notch in the blade
6 Drum cover
7 Drum
8 Triangular rule
9 Screwdriver
SPECIFIC ATIONS
Model
Planing width ............................................... 170 mm
Planing depth ................................................... 2 mm
–1
No load speed (min
) ................................... 15,000
Overall length ............................................... 529 mm
Net weight ....................................................... 8.8 kg
• Due to the continuing program of research and
development, the specifications herein are subject
to change without prior notice.
• Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and can only be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause volt-
age fluctuations. The operation of this device under
unfavorable mains conditions can have adverse
effects to the operation of other equipment. With a
mains impedance equal or less than 0.42 Ohms it can
be presumed that there will be no negative effects.
The mains socket used for this device must be
protected with a fuse or protective circuit breaker
having slow tripping characteristics.
Safety hints
For your own safety, please refer to enclosed safety
instructions.
Explanation of general view
0 Knob
q Switch trigger
w Lock button
e Lock-off button
r Start
t End
y Sharpening holder
u Wing nut
i Blade (A)
ADDITIONAL SAFETY RULES
1806B
1. Rags, cloth, cord, string and the like should
never be left around the work area.
2. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
3. Handle the blades very carefully.
4. Be sure the blade installation bolts are
securely tightened before operation.
5. Hold the tool firmly with both hands.
6. Keep hands away from rotating parts.
7. Before using the tool on an actual work-
piece, let it run for a while. Watch for vibration
or wobbling that could indicate poor installa-
tion or a poorly balanced blade.
8. Make sure the blade is not contacting the
workpiece before the switch is turned on.
9. Wait until the blade attains full speed before
cutting.
10. Keep at least 200 mm away from the tool
at all times.
11. Always switch off and wait for the blades to
come to a complete stop before any adjusting.
12. Never stick your finger into the chip chute.
Chute may jam when cutting damp wood.
Clean out chips with a stick.
13. Do not leave the tool running. Operate the
tool only when hand-held.
14. When leaving the planer, switch off and set it
with the front base up on a wooden block, so
that the blades do not contact anything.
15. Always change both blades or covers on the
drum, otherwise the resulting imbalance will
cause vibration and shorten tool life.
16. Wait for complete run-down before putting the
tool aside.
17. Use only Makita blades specified in this
manual.
SAVE THESE INSTRUCTIONS.
o Blade (B)
p Side (C)
a Side (D)
s Nozzle
d Makita vacuum cleaner
f Limit mark
g Chip cover
h Brush holder cap
5