Makita 2012NB 사용 설명서 - 페이지 6
{카테고리_이름} Makita 2012NB에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Makita 2012NB 17 페이지. Thicknesser
Makita 2012NB에 대해서도 마찬가지입니다: 사용 설명서 (13 페이지), 사용 설명서 (14 페이지), 사용 설명서 (13 페이지), 사용 설명서 (20 페이지)
페이지 인쇄
ENGLISH
1
Carrying handle
2
Sub-table
3
Bolt or screw
4
Pilot lamp
5
Switch
6
Crank handle
7
Scale
8
Main frame
9
Indicator plate
10 Depth gauge
11 Groove
12 Depth adjusting gauge
13 Stopper
14 Stopper button
SPECIFICATION
Model
Cutting width
Max. cutting depth
Feed rate (min
Table size (W x L)
No load speed (min
Overall length (W x L x H)
Net weight
safety class
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for planing wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.38 Ohms it can be presumed that
there will be no negative effects.
The mains socket used for this device must be protected
with a fuse or protective circuit breaker having slow trip-
ping characteristics.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
6
Explanation of general view
15 Stopper knob
16 Table top
17 Lock plate
18 Pulley
19 Drum
20 Chain
21 Thumb screw
22 Blade installation bolt
23 Set plate
24 Blade
25 Claw
26 Magnetic holder
27 Socket wrench
28 Blade installation bolt
–1
)
–1
)
29 Screw
30 Blade gauge
31 Hood set
32 Chip cover
33 Ruler
34 Post card
35 Adjusting screw
36 Hex wrench
37 Limit mark
38 Brush holder cap
39 Screwdriver
40 Column
41 Base
42 More than 4 mm
2012NB
304 mm
3.0 mm of stock width less than 150 mm
1.5 mm of stock width from 150 mm to 240 mm
1.0 mm of stock width from 240 mm to 304 mm
8.5 m
304 mm x 771 mm
8,500
483 mm x 771 mm x 401 mm
27 kg
ADDITIONAL SAFETY RULES
1.
Wear eye protection.
2.
Wear suitable personal protective equipment
when necessary, such as hearing protection (ear
plugs), respiratory protection (dust mask) and
gloves when handling rough material.
3.
Do not use the tool in the presence of flammable
liquids or gases.
4.
Make sure that all covers are installed in place
before operation.
5.
Handle the blades very carefully.
6.
Check the blades carefully for cracks or damage
before operation. Replace cracked or damaged
blades immediately.
7.
Tighten the planer blade installation bolts
securely.
8.
Remove nails and clean the workpiece before
cutting. Nail, sand or foreign matter can cause
blade damage.
9.
Do not remove chips from the chip chute when
the motor is running. Clean out chips after the
blades come to a complete stop. Always use a
stick etc. when cleaning them out.
10. Do not leave the tool running.
11. Do not abuse cord. Never yank cord to discon-
nect it from receptacle. Keep cord away from
heat, oil water and sharp edges.
SAVE THESE INSTRUCTIONS.
/II
ENB065-1