ALIBI ALI-NS3034R 빠른 설치 매뉴얼
{카테고리_이름} ALIBI ALI-NS3034R에 대한 빠른 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ALIBI ALI-NS3034R 6 페이지. Ip 4 mp ir bullet camera
페이지 인쇄
ALI-NS3034R IP 4 MP IR Bullet
Camera Quick Installation Guide
This document guides you through the basic steps to install and initially configure the ALI-NS3034R
camera. The ALI-NS3034R camera features:
1/3" progressive scan CMOS sensor, up to 2688 × 1520 resolution
•
2.8 - 12 mm motorized varifocal lens
•
120 dB True Day/Night (ICR), 3D DNR
•
-22˚F ~ 140˚F operating range
•
Smart IR array, 100 ft range, 850 nm
•
Video analytics: Tamper detection, Line crossing, Intrusion Detection
•
For more information, refer to these documents - available from your equipment vendor:
ALIBI™ Tools Utility Installation and User Manual
•
ALIBI™ Witness and ALIBI™ Witness HD Apps for Android - Quick Start Guide
•
ALIBI™ IP Camera Firmware Version x.x User Manual
•
Articulated
mounting
bracket
Camera body
IR array
Lens
Camera with sun shield and lens cover removed
* Press the RESET button for 10 seconds when the camera is powering on or rebooting to restore the
default settings, including the user name, password, IP address, the port number, etc.
www.observint.com
1
Junction box assembly
(see detail below)
Camera mounting base
Sun Shield
Lens cover
Reset button
SD card slot
Video test cable connector
Camera base
locator pins
Top (up)
Bottom (down)
Conduit port (2)
Junction box detail
What's in the box
Your camera includes these items:
Video test
cable
Weatherproof
LAN coupling
Surface
mount drill
template
Before installing the camera
Make sure the device in the package is in good condition and all the assembly parts are included.
•
Make sure all the related equipment is power-off during the installation.
•
Check the specification of the products for the installation environment.
•
Make sure the power supply is matched with your required voltage to avoid damage.
•
Make sure that the wall is strong enough to withstand three times (12 lb) the weight of the camera.
•
Dust or grease on the lens cover will cause IR reflection. Please do not remove the dome cover film
•
until the installation is finished. If there is dust or grease on the lens cover, clean the it with a clean
soft cloth and isopropyl alcohol.
Step 1.
Install a microSD card
A microSD card installed in the camera provides local storage for log information, capture files, and
recorded video. This information can be downloaded to a network PC by accessing the camera web
interface with Microsoft Internet Explorer (see "Step 5. Login to the camera" on page 4). microSD cards
can be as large as 128GB. To install a microSD card in the camera:
1.
Loosen the sun shield set screw, then lift off the sun shield.
2.
Remove the lens cover from the camera body by unscrewing it counterclockwise (observing it from
the lens end).
3.
Insert a microSD card into the slot shown in the photo to the left.
4.
Push the microSD card into the slot until it clicks into place.
5.
Reattach the lens cover and the sun shield.
Step 2.
Install the camera
The camera includes hardware to install it directly to a mounting surface or to the Junction box provided.
The camera can be installed on a ceiling (horizontal surface) or wall (vertical surface). To install the camera,
do one of the following:
Safety cable hook
Mounting screw
hole (4)
Hole for camera
mounting screw (3)
Cable access
through mounting
surface
Security
L-wrench
CD-ROM
manuals and
software
Mounting
hardware
packet
Junction box
(top view)
ALI-NS3034R_CQ
160315