ALIBI ALI-NS4022R 빠른 설치 매뉴얼 - 페이지 4

{카테고리_이름} ALIBI ALI-NS4022R에 대한 빠른 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. ALIBI ALI-NS4022R 5 페이지. Ip bullet cameras
ALIBI ALI-NS4022R에 대해서도 마찬가지입니다: 빠른 설치 매뉴얼 (6 페이지)

페이지 인쇄

Step 5.

Adjust the camera for your surveillance target

While observing live video from your camera in the Live View tab (see above), loosen the Pan,

Tilt and Rotation lock screws at least two turns using the security L-wrench provided, then move

the camera to point at the center of your surveillance target. Tighten the lock screws to hold the

camera in position.

Pan lock screw - Pan: 0˚ ~ 360˚

Tilt lock screw

Tilt: 0˚ ~ 100˚

Rotation lock screw

Rotation: 0˚ ~ 360˚

After adjusting the camera for the preferred field of view, click the Setup tab, and then click the

Image link in the left frame.

Adjust the Brightness Contrast, Saturation and Sharpness of the image as follows.

Image Adjustment submenu (see above): Adjust the Saturation, Hue, Brightness,

—

Contrast and Sharpness of the video image. Each parameter can be set to a level of

0 ~ 100 either by moving the slider or entering the value in the box on the right. The

effect of the adjustment will appear in the Live View image in the menu.

Open the other submenus on this screen. Adjust the following as needed. Refer to the Camera

Firmware User Manual for your camera for additional information about parameter settings.

Exposure Settings submenu: In this submenu, set the following for the best

—

performance:

Iris Mode: Select Auto or Manual. Some cameras may not offer both options.

Exposure Time: Value ranges from 1/3 to 1/100,000 s. The nominal value is 1/150.

Adjust it according to the lightening condition.

Gain: Set the gain to show the optimal brightness level.

Switch Day and Night: Select either Auto-Switch, Scheduled-Switch, or

—

Triggered by Alarm Input.

If using Auto-Switch, open the Day/Night Switch submenu to select the

Sensitivity, Filtering Time, and Smart IR feature ON or OFF.

If using Scheduled Switch, set the Start Time and End Time of the switch, then

open the Day/Night Switch submenu to select the Smart IR feature ON or OFF.

Also, click the Common, Day and Night tabs to set the Saturation, Hue, Brightness,

Contrast and Sharpness for Day and for Night modes.

Day/Night Switch submenu: You can set the Day/Night switch to Day, Night, Auto, or

—

Schedule. The option you select determines the submenu options.

Day or Night: These options both have one parameter: Smart IR.

Auto: If you select Auto switch, you can set the sensitivity (0 .. 7), filtering time and

Smart IR.

Schedule: Use Schedule to set that Start Time and End Time for the switch. Smart

IR is also selectable.

www.observint.com

Backlight Settings: Backlight settings include BLC Area (Off, Up, Down Left Right

—

Center), the area to control, and WDR (Wide Dynamic Range) ON or OFF.

White Balance: White Balance selection is used to correct colors in the image

—

depending on the lighting source. You can also set the white balance manually (MWB),

using Automatic White Balance (AWB1), and lock the white balance setting (Locked WB).

Image Enhancement: Options in this submenu include Digital Noise Reduction (DNR)

—

ON or OFF. If ON, you can also adjust the level of noise reduction.

Video Adjustment: Video Adjustment includes:

—

Mirror: Mirror adjustment enables you to flip the image (Up/Down), flip Left/Right

(reflect or Center).

Rotate: Rotate rotates the image +90 degrees. Rotate and Mirror can be used to

adjust the image in any orientation.

Video Standard: Select 60 Hz for NTSC format.

Capture Mode: To make a complete use of the 16:9 aspect ratio, you can enable the

capture mode when you use the camera in a narrow view scene.

Other: Options in this menu depend on the features of the camera.

—

Using the Waterproof Ethernet Fitting

Install the Waterproof Ethernet Fitting on the Ethernet cable end at the camera when moisture

or contamination exists in the area near the camera. The fitting includes several parts that must be

installed in a specific order. To install the fitting:

Place the rubber O-ring over the camera drop cable end cap.

Push the O-ring up to the connector cap.

Place the Lock Nut onto the network cable from the router

or switch as shown in the drawing to the right. The inside

threads must be toward the camera end.

Place the rubber basket onto the network cable above the lock

nut as shown.

Place the end cap onto the network cable above the rubber

gasket as shown. The fingered end must be toward the the

router or switch.

Install an RJ-45 connector onto the network cable.

Plug the RJ-45 connector with the network cable into the

camera network drop cable.

Fit the end cap on the network cable onto the camera drop

cable end cap. Rotate the network cable end cap to lock it in

place.

Push the rubber gasket fully into the end of the network cable

end cap.

Screw the lock nut onto the network cable end cap until it is

fully seated.

Network drop cable

from camera

Ethernet Fitting installed

Ethernet Fitting assembled and connected

Network drop

cable from

camera

Drop cable

end cap

Rubber

O-ring

seal

RJ-45

connector

End cap

Rubber

gasket

Network cable from

router or switch

Lock nut

Network

cable

from

router or

switch